seeking mainshaft sleeve help
Quote from Reloader on May 30, 2021, 11:52 amI have a worn out 1050 that needs a sleeve for the mainshaft.
Does anyone on this forum know where to get the sleeve and what size to bore the press out to accept the sleeve?It's an easy job I figure someone on this forum has done this and can share the material & type of sleeve they used and where to source it?
Thanks
I have a worn out 1050 that needs a sleeve for the mainshaft.
Does anyone on this forum know where to get the sleeve and what size to bore the press out to accept the sleeve?
It's an easy job I figure someone on this forum has done this and can share the material & type of sleeve they used and where to source it?
Thanks
Quote from Reloader on May 31, 2021, 1:19 amI don't have a 1050, RL or Super. How long of a bearing surface does it have inside the casting? And how long is the mainshaft?
How about just boring it out to 1.5" and making a new mainshaft. It looks like a simple part. McMaster-Carr has some ground shafts.
https://www.mcmaster.com/ground-shafts/diameter~1-1-2/linear-motion-shafts-with-machinable-ends/
Or maybe, after boring, press-in a piece of 1 ½" x .035" wall 4130 tubing? It is very strong and stiff. Then just turn/grind down the mainshaft to fit inside. Maybe get some dry ice to shrink it.
https://www.mcmaster.com/89955K389/
I'm afraid the threaded section for the shellplate retainer would be greatly weakened if bored-out much.
I don't have a 1050, RL or Super. How long of a bearing surface does it have inside the casting? And how long is the mainshaft?
How about just boring it out to 1.5" and making a new mainshaft. It looks like a simple part. McMaster-Carr has some ground shafts.
https://www.mcmaster.com/ground-shafts/diameter~1-1-2/linear-motion-shafts-with-machinable-ends/
Or maybe, after boring, press-in a piece of 1 ½" x .035" wall 4130 tubing? It is very strong and stiff. Then just turn/grind down the mainshaft to fit inside. Maybe get some dry ice to shrink it.
https://www.mcmaster.com/89955K389/
I'm afraid the threaded section for the shellplate retainer would be greatly weakened if bored-out much.
Quote from Reloader on June 1, 2021, 2:29 pmthanks for he advice, the shaft is fine its the wobble in the actual press, it needs a sleeve and from what I've been told their are people who do this, I'm being honest i'm cheap and can bore it out myself, I am hoping someone on this forum has done this and will share what they used, I really don't want to try and see method, I'm hoping someone who has done this will provide the details of how they did it?
thanks for he advice, the shaft is fine its the wobble in the actual press, it needs a sleeve and from what I've been told their are people who do this, I'm being honest i'm cheap and can bore it out myself, I am hoping someone on this forum has done this and will share what they used, I really don't want to try and see method, I'm hoping someone who has done this will provide the details of how they did it?
Quote from Reloader on June 1, 2021, 8:46 pmI found this thread from another forum and not much else.
https://forums.brianenos.com/topic/270800-dillion-press-frame-question/
I found this thread from another forum and not much else.
https://forums.brianenos.com/topic/270800-dillion-press-frame-question/
Quote from Reloader on June 1, 2021, 10:51 pm"the shaft is fine its the wobble in the actual press"
I was only suggesting the oversize or undersize mainshaft to avoid a large overbore that would weaken the threaded boss. $15.54 (plus shipping) for the 4130 sleeve and turning-down the mainshaft .050" or so– it's hard to imagine an easier or less expensive fix, unless their was a custom tailored solution.
"the shaft is fine its the wobble in the actual press"
I was only suggesting the oversize or undersize mainshaft to avoid a large overbore that would weaken the threaded boss. $15.54 (plus shipping) for the 4130 sleeve and turning-down the mainshaft .050" or so– it's hard to imagine an easier or less expensive fix, unless their was a custom tailored solution.
Quote from Reloader on June 2, 2021, 12:06 amI just measured my '650 shaft and it's around 1.498" in diameter. It might be longer, but possibly adaptable to an over-bored 1050– whichever exact machine you have, since there are two different machines with 1050 in the name. Assuming, of course, that your mainshaft is actually 1-31/64" in diameter and that Dillon would sell you one. The part is not actually listed for sale on the website.
I just measured my '650 shaft and it's around 1.498" in diameter. It might be longer, but possibly adaptable to an over-bored 1050– whichever exact machine you have, since there are two different machines with 1050 in the name. Assuming, of course, that your mainshaft is actually 1-31/64" in diameter and that Dillon would sell you one. The part is not actually listed for sale on the website.
Quote from neloril804@ on September 10, 2026, 8:51 amearning money online is just like earning money offline, it also takes a lot of work just to earn a penny.,IndoCair Daftar
earning money online is just like earning money offline, it also takes a lot of work just to earn a penny.,IndoCair Daftar
Quote from daniyal on September 15, 2026, 2:39 pmFantastic beat ! I wish to apprentice while you amend your website, how could i subscribe for a blog website? The account helped me a acceptable deal. I had been tiny bit acquainted of this your broadcast provided bright clear ideasitus dewa33
Fantastic beat ! I wish to apprentice while you amend your website, how could i subscribe for a blog website? The account helped me a acceptable deal. I had been tiny bit acquainted of this your broadcast provided bright clear ideasitus dewa33
Quote from daniyal on September 20, 2026, 1:33 pmI like what you guys are up too. Such smart work and reporting! Carry on the superb works guys I have incorporated you guys to my blogroll. I think it’ll improve the value of my web site nohu90 com
I like what you guys are up too. Such smart work and reporting! Carry on the superb works guys I have incorporated you guys to my blogroll. I think it’ll improve the value of my web site nohu90 com
Quote from daniyal on September 22, 2026, 12:14 pmWith havin so much content do you ever run into any issues of plagorism or copyright infringement? My website has a lot of exclusive content I’ve either created myself or outsourced but it appears a lot of it is popping it up all over the internet without my authorization. Do you know any methods to help prevent content from being ripped off? I’d genuinely appreciate it. togel hk
With havin so much content do you ever run into any issues of plagorism or copyright infringement? My website has a lot of exclusive content I’ve either created myself or outsourced but it appears a lot of it is popping it up all over the internet without my authorization. Do you know any methods to help prevent content from being ripped off? I’d genuinely appreciate it. togel hk