Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
My XL750 has no loctite on anything. I had it completely disassembled and re-assembled over the wee …In: Primer Chute Screws
6 years ago
Not a bit of Loctite to be found. They were apparently torqued with a train axle wrench.
One came …In: Primer Chute Screws
6 years ago
On the XL750, what flavor of Loctite or equivalent is used on the screws for the primer chute? I ha …In: Primer Chute Screws
6 years ago
A few years ago I switched to Dillon Case Lube and experienced a couple of stuck cases. Maddening a …In: 223 Stuck Case(s)
6 years ago
Yes it is the sizing die. I destroyed it attempting to remove the stuck. I will order another one …In: 223 Stuck Case(s)
6 years ago
Assuming you are speaking about the resizing die, I would make sure there is no excess lube/dirt/wha …In: 223 Stuck Case(s)
6 years ago
I am an experienced 550B/223 reloader using Dillon case lube. Over the past several months I have b …In: 223 Stuck Case(s)
6 years ago
There is another way. I empty the powder from my powder measure at the conclusion of every reloadin …In: Powder measure
6 years ago
To remove the powder from the powder measure, I loosen the two bolts on the collar holding the powde …In: Powder measure
6 years ago
And I loaded several hundred rounds today - checking powder weight pretty often and all is good so …In: Powder measure
6 years ago
Okay so I kept messing with the powder measure and also read up on it some and as it turns out by ad …In: Powder measure
6 years ago
So I have a 550B that I have been loading .357 mag (been loading .45 acp also)
So for the .357 I ha …In: Powder measure
6 years ago
as long as you keep velocities under 1200 fps, and don't overcrimp, no problem loading plated …In: 357 bullets
6 years ago
Have 38 spec plated bullets. About to begin to load a 357 casing for target practice and using a lig …In: 357 bullets
6 years ago
Also interested in this. Got a pile of 300 and 338 norma mag brass just waiting to go...In: .338 Lapua
5 years ago
What is the status of the 338 Lapua Conversion kit for the XL750?
Respectively what's the timel …In: .338 Lapua
5 years ago
6 years ago
we are waiting for the shellplate to be finished, then we will have a conversion kit for 338 Lapua. …In: .338 Lapua
6 years ago
Good Day,
What conversion kit etc do I need to use to load .338 Lapua on the XL750? Additionally, …In: .338 Lapua
6 years ago
This varies depending on whether you are loading a straightwall handgun cartridge or a bottlenecked …In: Powder Bar Travel
6 years ago
On the bottom of page 25 Section 8.3.3 and mainly 8.3.4 in the instructional manual it states that t …In: Powder Bar Travel
6 years ago
I wouldn't wish that P.O.S. on a broke dick dog. I'd feel guilty if I passed on garbage li …In: Do lemons exist?
6 years ago
Oh yeah!!! my 650 has been a POS since the first day I set it up I have never successfully primed o …In: Do lemons exist?
6 years ago
Primer problems can be caused by a variety of things, all of which can be easily resolved over the p …In: Do lemons exist?
6 years ago
Have called Dillon? If not, I'd call and see if they can get you fixed over the phone without …In: Do lemons exist?
6 years ago
Ok, I've tried being real patient with my XL650 over the years but to no avail. I have had not …In: Do lemons exist?
6 years ago
223 dies work fine for 5.56mm. I'm not aware of anyone offering the higher pressure load data f …In: .223 dies for loading 5.56 nato
6 years ago
Can the .223 dies set be used to load 5.56 NATO and if so where can I find load data and 550B setup …In: .223 dies for loading 5.56 nato
6 years ago
Having the same issue. Just got the strong mount and it works great of the press but the cartridge …In: Wrong finished cartridge chute in strong mount box?
6 years ago
They have 7 holes, and they hold the press properly, it's only the chute that has the issue.In: Wrong finished cartridge chute in strong mount box?
6 years ago
how many holes are in the center area of the side of a strong mount plate, 4 or 7? For the 550 it s …In: Wrong finished cartridge chute in strong mount box?
6 years ago
I recently purchased my second 550 from a stocking retailer along with a roller handle and strong mo …In: Wrong finished cartridge chute in strong mount box?
6 years ago
https://www.dillonprecision.com/die-decapping-assembly-parts_8_4_24507.html
13269In: 223 Expander Ball
6 years ago
I have been having an issue while reloading 223. I have noticed some brass shavings on my reloading …In: 223 Expander Ball
6 years ago
Well another 4 weeks has passed since my last update and still no RL 1100. Four months have passed s …In: RL1100 Problems??
6 years ago
Mine was ordered in 223 and spoke to Gary the other day and was told they have machines built but ar …In: RL1100 Problems??
6 years ago
WVULTRA, I know a couple that ordered and received their RL1100 9mm presses just a couple weeks ago …In: RL1100 Problems??
6 years ago
And the RL1100 page states this:
"Please note: Due to overwhelming demand, machine orders are …In: RL1100 Problems??
6 years ago
Ok Admin..........I'm just over 12 weeks since ordering the RL1100 in 9mm........is the only ho …In: RL1100 Problems??
6 years ago
6 years ago
Don’t feel bad. I ordered mine January 21st and still haven’t seen it yet. 4 to 6 weeks when I order …In: RL1100 Problems??
6 years ago
orders come in faster than we can get parts in to build them, and dies come in and out of stock. We …In: RL1100 Problems??
6 years ago
What's up with the RL1100 orders and delivery's. Ordered my RL1100 in 308 Win in Mid Febru …In: RL1100 Problems??
6 years ago