Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
Also, can you please help with the occasional problem where the primer does not seat fully. I' …In: Primers not
6 years ago
Hello: Newcomer to Dillon world and could not be happier.
When I deprime spent pistol cases, many o …In: Primers not
6 years ago
I use Use 30 weight motor oil on the shaft and Lucas Marine grease (blue) everywhere else grease is …In: Grease brand
6 years ago
Page 43 of the owners manual:
Maintenance
Lubrication: Operating circumstances will
dictate the freq …In: Grease brand
6 years ago
6 years ago
What type of grease should I use to lube my XL650. I have some shooters choice that is used for lubi …In: Grease brand
6 years ago
I am using one or two Powder Measures on my 750, both of which were purchased with my 550B.In: 550 fail safe powder measure
6 years ago
According to the Latest Dillon Catalog ( May 2020 ) the part number for the powder measures for the …In: 550 fail safe powder measure
6 years ago
Would someone know if a 550 Fail Safe Powder Measure work on an XL750?
Thank youIn: 550 fail safe powder measure
6 years ago
In the other thread About the XL750 and Bulletfeeder, there’s a comment that Double Alpha is manufac …In: using a RCBS measure ???
6 years ago
I agree with you Dillon has done us a disservice I bought my XL750 with a plan to add a Mr Bullet fe …In: using a RCBS measure ???
6 years ago
I did read one thread on another forum about a guy who has it working with a “green” case activated …In: using a RCBS measure ???
6 years ago
Is anyone here using a case activated RCBS powder measure on their XL750 I've heard you can use …In: using a RCBS measure ???
6 years ago
you can try backing the collet sizer in station one up 1/2 turn, but ultimately the problem is defec …In: Bases coming off holls
6 years ago
Using STS hulls about every 10 hulls it pulls the base off in station 2 took the clip off the die a …In: Bases coming off holls
6 years ago
Excellent, and thank you. I did some reloading about 20 years ago, and just getting back into it, s …In: 550 tube pak only had 3 tubes
6 years ago
3 is correct. One primer magazine tube is already installed in the loaderIn: 550 tube pak only had 3 tubes
6 years ago
The 550 tube pak with my RL 550C only had 3 tubes, and it looked like maybe it should have had 4. I …In: 550 tube pak only had 3 tubes
6 years ago
Part 13921Powder bar spacer plug is used to hold spacer 13644 in when you are using the small 20062 …In: Part 13921
6 years ago
I upgraded my powder measure from the old spring system. Part 13921 fell out. I cant find how to re …In: Part 13921
6 years ago
Thanks to Dillon for aiding me with my SD repair. I notice my very old SD was not fully seating sma …In: successful repair with shell plate.
6 years ago
Yes I meant the bullet PULLER, sorry about that.....and thank you for the conversion I just wanted …In: Bullet Puller
6 years ago
6 years ago
Do you mean bullet puller? In your question you say bullet feeder. The Berry's bullet puller wi …In: Bullet Puller
6 years ago
Does the Bullet feeder listed for sale by Dillon do .357 caliber ? It is not listed as being one of …In: Bullet Puller
6 years ago
Thank you Admin! Your comment about station 4 appears to have fixed my high primer issue. Apprecia …In: Primer seating depth 9mm case
6 years ago
Push down on the edge of the shellplate at station 4. If it feels springy, then the shellplate bolt …In: Primer seating depth 9mm case
6 years ago
On CBC cases I found hard to seat the primer correctly and some primer (Fiocchi SP) are protruding t …In: Primer seating depth 9mm case
6 years ago
I had the same problem on my 750. I believe the small plastic tip on the primer magazine was too ti …In: New press setup issues
6 years ago
Here are the issues I experienced getting my press setup...
A. Bench is just over 1 - 3/4 thick...u …In: New press setup issues
6 years ago
Hi lacoppari
Thank you very much for your fast answer! That make sense! 🙂 Than I dissable & cl …In: Primer Problems
6 years ago
Your English is very understandable. You may have either dirt or lubricant at the bottom of the pr …In: Primer Problems
6 years ago
Hello from Switzerland!
I hope you are well at this difficult time.
Sorry, but my english is not so …In: Primer Problems
6 years ago
e-mail us for a return authorization to repair your die. Please include your address. We'll hav …In: Sizing Ring Separation
6 years ago
6 years ago
6 years ago
I am currently loading .380 acp on a 550B press. Today on the up stroke the sizing ring separated fr …In: Sizing Ring Separation
6 years ago
Do cartridges that fail to ignite on the first firing pin strike ignite on a second strike? If yes, …In: ppq not reloading
6 years ago
I have setup my Reloader , but the shells wont fit in my 9MM Polymer Frame Walter q5 match. The prob …In: ppq not reloading
6 years ago
Had this problem with some .30 Carbine cases recently. Tall thin cases. The bolt through the shell h …In: Damaging shells
6 years ago
My first guess is you have a wrong locator pin installed at position 3. For 9mm, you need #3 pinsIn: Damaging shells
6 years ago
I just changed the reloader from 38 to 9mm. When I tested powder loads I had no problems, but when t …In: Damaging shells
6 years ago
no, the primer slides are of different lengths, and the cup height is different as wellIn: Primer Slide Bar
6 years ago
I'm wondering if the 750 Primer Slide Bar has the same dimensions as the one in the 550?
The sl …In: Primer Slide Bar
6 years ago
thanks for the reply. i'll be reloading .45acp can you see any reason the adapter wouldn't …In: powder measure
6 years ago
we offer a powder measure adapter, #20029. Use this with the RL450 powder die #20308. This allows yo …In: powder measure
6 years ago
I'm new to reloading with a couple questions. I've got an RL450 with out the powder measur …In: powder measure
6 years ago