Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
can you seat the bullet by hand? Being able to turn the bullet in the case after crimping indicates …In: Sizing Die Problem
14 years ago
I have the same problem when loading .38 sp - the projectile just slides in to the case even af …In: Sizing Die Problem
14 years ago
larry351, we have already replied to your situation previously. If you are still having proble …In: Sizing Die Problem
18 years ago
Since you stated that you load for 9mm make sure you're not using bullets for 9mm as they are t …In: Sizing Die Problem
18 years ago
Yes, the 125 gr bullets, running even 1/2 thousandth undersize in conjunction with thinner Remington …In: Sizing Die Problem
18 years ago
Thanks Dillon; I am using 125Gr. JHP, I didn't know that there could be a problem when us …In: Sizing Die Problem
18 years ago
Are you using 110 gr. or 125 gr. jacketed bullets with this brass? If so it is simply a compat …In: Sizing Die Problem
18 years ago
Feelthy I measured the Bullets and they were .3565, I don't think this is the problem.  …In: Sizing Die Problem
18 years ago
Larry, Using a micrometer, measure/check the OD of both: the Dillon neck expander die & (of co …In: Sizing Die Problem
18 years ago
I have just started reloading 38 Spec. on my Dillon 550B, using Dillon Dies. I ran into a problem wh …In: Sizing Die Problem
18 years ago
18 years ago
wait.. you have an OAL varience of 5 HUNDRETHS of an inch?? .05? I'm assuming you m …In: 550 modifications
18 years ago
I added .010 brass shim stock at the base of the toolhead to reduce slop, this did reduce my OAL var …In: 550 modifications
18 years ago
These products from non-Dillon sources tend to work as advertised and will take movement out of the …In: 550 modifications
18 years ago
Whats with these aftermarket items to take the slop out of 550 Shellplate and Toolhead? Are they wor …In: 550 modifications
18 years ago
I am having the same problem with my 45 Long colt set up. I have been loading 45 ACP for quite som …In: Problem with 45ACP shell plate alignment
18 years ago
I'm having the same problem. Mine is with the .223 conversion kit. I called once an …In: Problem with 45ACP shell plate alignment
18 years ago
Check to make sure that your shellplate has a #1 stamped on the top of it. Next loosen the loc …In: Problem with 45ACP shell plate alignment
18 years ago
First of all let me say that I'm still pretty new to the Dillon 550B. Just bought it a few mont …In: Problem with 45ACP shell plate alignment
18 years ago
17 years ago
Dillon, you need to start publicizing this nationally. If a new Con-Con comes about, the RKBA …In: Barak Obama announces his gun control plans
17 years ago
get em while you still can and stock up for what's comin down the pipeline in the not so distan …In: Barak Obama announces his gun control plans
18 years ago
Didn't we see this coming? I especially enjoyed "They also support making the expired fede …In: Barak Obama announces his gun control plans
18 years ago
Anyone who doesn't see B. Hussein Obama for what he is, deserves what they are going to get if …In: Barak Obama announces his gun control plans
18 years ago
Anyone voting for this man is voting for government slavery. An unarmed citizen is a is a serv …In: Barak Obama announces his gun control plans
18 years ago
http://www.barackobama.com/issues/urbanpolicy/ Scroll down to "crime and law enforcement" …In: Barak Obama announces his gun control plans
18 years ago
I HAVE 3 BRAND NEW DILLON COUNTERS PUTTING ON EBAY TODAY PLEASE ADVISE IF YOU WOULD LIKE $20.00 EA. …In: Dillon Cartridge Counter Parts
18 years ago
Do you know where I can get parts for a Dillon cartridge counter? I am looking for the mounting brac …In: Dillon Cartridge Counter Parts
18 years ago
When did Dillon stop selling Dillon Case Lube 5000 in the aerosol cans and make the switch to the pu …In: Dillon case lube 5000
18 years ago
The standard large powder bar drops up to mid-50 grain range of extruded powder, and up to about 60 …In: 7mm Rem Mag
18 years ago
I understand different powders have different density, but as a general rule do I need the Magnum po …In: 7mm Rem Mag
18 years ago
That did the trick. A little sure goes a long way.
One more question. Do you recommend sizing a …In: .308 Sizing Problem
18 years ago
When you adjust the size die, run it down until it makes contact with the shellplate, then turn the …In: .308 Sizing Problem
18 years ago
I just installed a Dillon .308 set of dies on my 550. I have not been able to get the sizing d …In: .308 Sizing Problem
18 years ago
I appreciate the info. I too had to lock down the Lee die from underneath on my 650. I was having fe …In: Die too short to lock down
16 years ago
I expected with the avatar you had your humor would show through. The solution is to use locki …In: Die too short to lock down
16 years ago
Oh boy now it starts! Why re-invent the wheel? If I can make the Lee dies work then why spend the ex …In: Die too short to lock down
16 years ago
Switch to Dillon dies and no problems. Leave those Lee dies for the ones using a inferior relo …In: Die too short to lock down
16 years ago
ok I'm in the same boat but I have not purchased the 550B yet. I have Lee dies in 45ACP, 9MM, 4 …In: Die too short to lock down
16 years ago
Most of THE various Lee dies I use on my 550 & 650 are a bit short. Sometimes i put the lock r …In: Die too short to lock down
18 years ago
Until very recently, Lee dies were on the short side. You can use a lock ring on the underside, or, …In: Die too short to lock down
18 years ago
Is there any reason why I can't lock down my Lee .223 re-sizing die from below the toolhead? Th …In: Die too short to lock down
18 years ago
Open up the latter half of the XL650 manual. Page 32 shows setup for the powder check. You need to p …In: Powder Check
18 years ago
18 years ago
Phone or email with your name and address, and ask for a 1050 manual. We are happy to mail one to yo …In: Powder Check
18 years ago