Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
The Lyman M die should open the neck enough that the flat base of the bullet drops well below the le …In: Flat based bullets in MBR
8 years ago
I did some research before buying a MBR for the 650. Found a lot of folks that had problems keeping …In: Flat based bullets in MBR
8 years ago
I have a 550 and I have had the same problem with high seating primers. The pin that pushes the prim …In: 550 primer seating problem
5 years ago
I find the stem and cup need to be seen too from time to time anyway. Another source of problems is …In: 550 primer seating problem
6 years ago
" Look closely at the spring. Springs sometimes just get tired and no longer fulfill their func …In: 550 primer seating problem
6 years ago
From your description of the problem, erratic primer seating, I suspect the culprit is the height of …In: 550 primer seating problem
6 years ago
I have been using my 550b for some years now and suddenly in the middle of a batch of reloads I beg …In: 550 primer seating problem
6 years ago
k38, I once had a problem with primers not seating deep enough and called Dillon about it. I was to …In: 550 primer seating problem
8 years ago
jforwel--
I called Dillon and the tech said there was no way to adjust the primer cup height. Was …In: 550 primer seating problem
8 years ago
What is the parts number of that screw? Also, I'm puzzled by the identification of the roller …In: 550 primer seating problem
8 years ago
Push down on the edge of the shellplate between stations 2 and 3. If it feels springy, then the shel …In: 550 primer seating problem
8 years ago
First, the primer cup has a small set screw for adjusting the height. Take out the slide bar, and u …In: 550 primer seating problem
8 years ago
I purchased a new 550C in November last year. I have loaded about 500 rounds for 38 specials and had …In: 550 primer seating problem
8 years ago
8 years ago
Just received a replacement body collar for my powder measure, but did not receive instructions. Ca …In: Body Collar replacement
8 years ago
8 years ago
To remove the square shaft assembly from your Square Deal, proceed as follows:
Detach the loaded car …In: Index mechanism jammed
8 years ago
My square deal has jammed up. It will not go up are down. On closer inspection i can see from the si …In: Index mechanism jammed
8 years ago
Tom, See figure 158 on page 33 of the xl 650 manual. It will show where the shellplate setscrew is …In: 2 650XL questions
8 years ago
OK, I will give those suggestions a try.
How do I tighten the shell plate ?
thanks,
TomIn: 2 650XL questions
8 years ago
On upside-down cases, either there is too much brass in the bowl, or the bowl is swaying and flippin …In: 2 650XL questions
8 years ago
I was getting more like 8-10 high primers per hundred, and the advice I got from Dillon customer ser …In: 2 650XL questions
8 years ago
I caught my press moving slightly when seating a primer. I had used screws in the rear and bolts in …In: 2 650XL questions
8 years ago
I have loaded about 12000 rounds 9mm on the 650 but had 2 questions:
1) Is there a way to adjust th …In: 2 650XL questions
8 years ago
Please either phone us, or email us and we will mail some tips to you. If you email, please include …In: Primers falling through
8 years ago
Sorry, just saw that you weren’t Dillon replying, l don’t expect you to send me a replacement tip 🙂In: Primers falling through
8 years ago
Forgot to mention that l also changed the blue plastic tip,9 mm, so it’s brand new and not the reaso …In: Primers falling through
8 years ago
It sounds like your Plastic Magazine orifice is broken, the red or blue end of the magazine inside t …In: Primers falling through
8 years ago
I ran into a new problem for me today when reloading, the primers started to fall through the machin …In: Primers falling through
8 years ago
Thank you,
I was able to find the o-ring at Home Depot. Here is the information:
3/4" OD x 5/ …In: Kinetic bullet puller
8 years ago
The o-ring for my Dillon bullet puller have broken into multiple pieces so I cannot get an accurate …In: Kinetic bullet puller
8 years ago
Sorry, I read your reply wrong, got it figured out and got them ordered...Thank you.In: 6.5 Creedmoor
8 years ago
https://www.dillonprecision.com/powder-funnels_8_48_25279.html
Then use the dropdown menu to select …In: 6.5 Creedmoor
8 years ago
How do I ordeer 6.5 Creedmoor funnel is #18947 ? The only one that comes up is Plastic Funnel
Stock …In: 6.5 Creedmoor
8 years ago
The plastic funnel is sold separately from the AT500 powder die.
The 6.5 Creedmoor funnel is #18947 …In: 6.5 Creedmoor
8 years ago
OK, Never mind. Think I got it...However does the Plastic Funnel (16617) come with the AT 500 Powder …In: 6.5 Creedmoor
8 years ago
I would like to load 6.5 creedmoor on my 550 but I do not want to use the powder measure...I want to …In: 6.5 Creedmoor
8 years ago
I have an extra set of dies for 45acp for sale for $47 shipped. New dies.
https://www.1911addicts. …In: Unused set of 45acp dies
8 years ago
The number is stamped onto the top of the pinIn: Case sticking between position 1 and 2 on plate rotation
8 years ago
Hi,
Yes Im going to look at the spring/detent distance when I get home tonight. I'm fairly ce …In: Case sticking between position 1 and 2 on plate rotation
8 years ago
The spring-loaded finger should guide the case back into the shellplate slot as it rotates towards s …In: Case sticking between position 1 and 2 on plate rotation
8 years ago
Hi all,
I've had my press for about 4 months, and have loaded 3-4,000 rounds thus far.
Recent …In: Case sticking between position 1 and 2 on plate rotation
8 years ago
We had problems that our Case Insert Slide was way too lose and stuck in it´s rear position.
Sportec …In: Case Insert Slide Derails
8 years ago
We ad problems that our Case Insert Slid was way too lose and stuck in it´s rear position.
Sportec A …In: Case Insert Slide Derails
8 years ago
Xx14n, my problem was solved when I added grease to the base of the Station 1 locator. It sticks t …In: Case Insert Slide Derails
8 years ago