Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
I can't recall the supervisor's name, but I placed the call at approximately 6:00 PM Centr …In: “Muddle through”
7 years ago
My apologies for the lack of service you received. I wish I knew which supervisor you dealt with. Ex …In: “Muddle through”
7 years ago
I bought a 650 about a week before they came out with the 750. I called and found out that for $50 e …In: “Muddle through”
7 years ago
So i fixed this just by rotating the powder drop so the bar was out of the way, and then running a s …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
i have the short one and it works.
but i did email them about a large one here is what they said.
D …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
I can confirm that with the short DAA powder bar installed in the XL750 you can run the Mr. Bulletfe …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Yes. A Short Powder Bar from DAA.
I made a Video.In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
DAA have manufactured a shorter replacement powder charge bar.
Shipment expected within the next two …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
I have been running a Lee auto drum on my 750 with good results. Very accurate and you can have a bu …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Just a note on my last post. If using the new springs from dillion you will need to use 2 springs.In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Simple fix that I did for now until the fix is available. Take off the fail safe bar. Zip tie togeth …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Message from DA
DA are currently working on a solution – which is a modified and shorter Dillon cha …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
With the global supply chain being what it is, I think it may be a bit of a wait. Still, when it’s a …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
I spoke to a Australian Dillon distributer a few hours ago.
Good news - Double Alpha are currently m …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Bistlinec, if you have a solution, could you please paste a photo (or link to one) showing what you …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
I've found to fix the problem is simple. Move the plate that anchors the powder priming arm 1 h …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Would using x2 part #14036 (the old pre 2000 powder bar return spring) in lieu of the safety return …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Our engineers sent their observations and potential solutions to Double Alpha. Since the Mr Bulletfe …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
Does anyone know if Dillon has addressed this issue or is it still ongoing? Was looking to purchase …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
For what it’s worth, I solved this problem by going to a green powder measure (which I had) and a ca …In: Mr. Bullet Feeder does not work properly on XL750?
6 years ago
My complaint is that I specifically emailed Dillon prior to purchasing the new 750 and detailed my s …In: Mr. Bullet Feeder does not work properly on XL750?
7 years ago
“We here at Dillon understand the issue concerning the simultaneous use of the bullet feeder and the …In: Mr. Bullet Feeder does not work properly on XL750?
7 years ago
Several queries now into Dillon.
They just act arrogant, know it all, do not address issue, and the …In: Mr. Bullet Feeder does not work properly on XL750?
7 years ago
There is nowhere on this site to e-mail pictures, post pictures, nothing.
I sent issue over form to …In: Mr. Bullet Feeder does not work properly on XL750?
7 years ago
Thanks for that Dillon works great now.In: primer system assembly assem/disassembly instructions needed. needed
7 years ago
In the XL650 manual, page 39, figures 194 and 195In: primer system assembly assem/disassembly instructions needed. needed
7 years ago
After having multiple primer explosion and getting a new primer system assembly from Dillon Aust, I …In: primer system assembly assem/disassembly instructions needed. needed
7 years ago
Actually, I believe the small base die will full length size but I had to back this die out a bit in …In: Full length size without deprime rod in die
7 years ago
The RCBS small base die only sizes the lower portion of the case (i.e. near the case head).In: Full length size without deprime rod in die
7 years ago
Skigrinder,
doesn't your small base die peform the full length resize?
Sounds to me like you ar …In: Full length size without deprime rod in die
7 years ago
Hi,
I'm setting up a .308 case prep toolhead for my XL650:
Station 1 - RCBS small base siz …In: Full length size without deprime rod in die
7 years ago
Manuals should be up on the website sometime next week. Parts will take a bit longer, not until aft …In: Rl1100 release date
6 years ago
When will online manuals and parts be available for the 1100? I’d like to upgrade my 1050 primer sta …In: Rl1100 release date
6 years ago
We started shipping machines yesterday. We have quite a few backorders to get out, but parts are com …In: Rl1100 release date
6 years ago
Here it is, late December and still no rl1100. What is the release date now? Late January?In: Rl1100 release date
6 years ago
We are using some new technology for some parts for the RL1100 and CP2000. The parts will be harder …In: Rl1100 release date
7 years ago
I want to start off by saying I’m a huge fan of your products. I own a decked out 650 and have been …In: Rl1100 release date
7 years ago
Forgot mention press been idle good while. I cleaned it up and lubed it well before started and moun …In: 650 Issues Timing
7 years ago
I just bought out my cousin reloading setup a XL650 with casefeeder and extras for $350 total. Thoug …In: 650 Issues Timing
7 years ago
From my experience the no BS warranty is spot on. You do have to pay postage to get your item to th …In: Inherited 550
7 years ago
Broken and worn parts are covered under warranty. Missing parts are not under warranty.In: Inherited 550
7 years ago
7 years ago