Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
In my 650 I lube all my cases before I drop them into the case feeder. Nothing fancy , I use n old B …In: to lube or not to lube
16 years ago
We lube everything here when we load, even 9mm and .380. It makes it easier to pull the handle. 9mm …In: to lube or not to lube
16 years ago
I wouldn't think you would lube for either cartridge if you were using carbide dies. I wouldn& …In: to lube or not to lube
16 years ago
After I converted my 650 from .40 S&W to 9mm Luger, I noticed that the effort in cycling the han …In: to lube or not to lube
16 years ago
Wow. Didn't take long for me to figure out how wrong I was. Dropping a cartridge into the die …In: Lee Factory Crimp Die on the 550B
8 years ago
Old thread, but found this searching for answers to the same issue. Here's why I think this IS …In: Lee Factory Crimp Die on the 550B
8 years ago
16 years ago
DID THE SOULUTION PRVIDED BY DILLON HELP BERNSNIELEE ? I HAVE THE SAME ISSUEIn: Lee Factory Crimp Die on the 550B
16 years ago
While you won't damage the machine by adjusting the crimp die down to contact the shellplate, t …In: Lee Factory Crimp Die on the 550B
16 years ago
Just started setting up My Dillon 550B and ran accross a concern on the fourth station where I am se …In: Lee Factory Crimp Die on the 550B
16 years ago
You may want to slight reform your magazine at the top a little narrower. It doesn't take much. …In: .40 S&W Loads on 550B
16 years ago
Appreciate the help - these mags are about 17 years old so I bet I have an old follower - we� …In: .40 S&W Loads on 550B
16 years ago
Be sure you have a newer style follower, marked #6 or higher. Weak mag springs can cause this as wel …In: .40 S&W Loads on 550B
16 years ago
No actually bought a Lone Wolf years ago - but prior to that I'd shoot a max of 100 rounds befo …In: .40 S&W Loads on 550B
16 years ago
Are you using the factory barrel in your Glock? If so, the use of lead bullets is not recommended, a …In: .40 S&W Loads on 550B
16 years ago
Re-loaded .40 S&W rounds on my 550B for this first time this week - 175 Gr LSWC, 5.6 …In: .40 S&W Loads on 550B
16 years ago
I HAD A SIMILER ISSUE IN REGARDS TO THE PRIMER CUP NOT GOING ALL THE WAY BACK ...AND NOT PICKING UP …In: 550 Primer Cup Problem
16 years ago
So far so good. Today I seated ten primers in a row with no problems whatsoever.In: 550 Primer Cup Problem
16 years ago
I did not tighten the two allen screws very tight either....You may want to loosen them if this fix …In: 550 Primer Cup Problem
16 years ago
I did not tighten the two allen screws very tight either....You may want to loosen them if this fix …In: 550 Primer Cup Problem
16 years ago
Something else to watch for is if the two primer system mounting bolts are grossly over-tightened, t …In: 550 Primer Cup Problem
16 years ago
Just started setting up my 550B today and I had the exact same problem!!! My buddy recommended check …In: 550 Primer Cup Problem
16 years ago
I changed out my primer slide assembly and installed the one for small pistols to begin loading …In: 550 Primer Cup Problem
16 years ago
this must be the month to break ring indexer! i just finished replacing mine . Did the same idea pro …In: Putting on springs
16 years ago
I broke the ring indexer on my 650 this past weekend and I noticed that there were some complaints a …In: Putting on springs
16 years ago
I'm looking for loadings with 180-190gr GC bullets for the Rem Max. My load for …In: Cast bullets & .357 Rem Max
16 years ago
I give up, if there was ever a worthless POS it's that primer crusher on the 650. I want to rem …In: Primers -- Help
13 years ago
I didn't want to start a new topic when my issue is with primers. So here it is. I …In: Primers -- Help
15 years ago
I use nothing but Wolf Primers so far so good. I trashed a few WWC brass cant get primers to seat,I …In: Primers -- Help
16 years ago
16 years ago
Hi,
I have been using Wolf recently because that is all that is available. I have had similar pr …In: Primers -- Help
16 years ago
Just want to add one other item to be on the lookout for. Make sure you clean your entir …In: Primers -- Help
16 years ago
A month ago I had problems with this and I ended up replacing the chrome plated arm that moves the p …In: Primers -- Help
16 years ago
Dillon, I will give that a try and call when I can get in front of the machine.
I appreciate the …In: Primers -- Help
16 years ago
I strongly suggest that you phone Dillon for assistance when you can be in front of the machine. The …In: Primers -- Help
16 years ago
I don't think it's the primers... I've loaded 1000's of rounds of 308 (mil brass …In: Primers -- Help
16 years ago
What is it with Primers....or is it me.My 650 does NOT like CCI, Wolf and now Federal Primers. They …In: Primers -- Help
16 years ago
Finally figured it out. The index pawl had burrs on it where it pops up into the shellplate.&# …In: Index Ring sticking
16 years ago
Yes there is grease on the inside. It is like it is catching on something but I have torn it c …In: Index Ring sticking
16 years ago
I am having a problem with the index ring stick to the rear and when I move the ram down, does not i …In: Index Ring sticking
16 years ago
While Dillon does not offer dies, I obtained my personal set from www.redding-reloading.com This i …In: 9.3x62 die and conv kit
16 years ago
Got a reply from Dillon Tech that there is no dedicated conversion kit, instead use the .30-06/.308 …In: 9.3x62 die and conv kit
16 years ago
Hi, I am just about to start reloading 9.3x63 but could not find any dies or conversion kit for my …In: 9.3x62 die and conv kit
16 years ago
For .270 Winchester and 30-06, the shellplate and locator pins. Only the powder funnels differ. Buy …In: caliber conversion kits
16 years ago
Yes you can purchase the individual parts see "Caliber Conversion Kit Individual Parts" on …In: caliber conversion kits
16 years ago
I recently received a RL 550 B as a gift and want to reload the .270 win and the 30-06. What I …In: caliber conversion kits
16 years ago
16 years ago