Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
There is a small 3oz, hand held grease gun by KEYSCO (Grainger item #46D308) that will easily inject …In: Lubrication Points
11 years ago
How are your link arms attached, via E-clips or nylock nuts? If clips, then the lower4 pin may be lu …In: Lubrication Points
18 years ago
i dont have a grease gun.. and if possible i'd like to be able to take the legs off for cleanin …In: Lubrication Points
18 years ago
For lubing the shaft, pul the handle down, apply several large DROPS of motor oil, then cycle the ha …In: Lubrication Points
18 years ago
I attempted to "upgrade" my RL550 by drilling grease holes. I found the material was hard …In: Lubrication Points
18 years ago
18 years ago
Dillon, I have an old RL550 and would like to modify it for grease gun lubrication. What size drill[ …In: Lubrication Points
18 years ago
18 years ago
Is there a specific lubrication point for the main shaft using 30 weight motor oil, or just apply it …In: Lubrication Points
18 years ago
http://www.azgfd.gov/inside_azgfd/documents/080119CommissionAgenda.pdfIn: Arizona Game & Fish Dept considers Lead ammunition restrictions
18 years ago
Extruded powder, while not quite as consistant as ball/spherical powder, meters wretty well into cal …In: Loading for 30-06
18 years ago
I thought you could not use extruded powder with the XL650? Mine used to throw many different powder …In: Loading for 30-06
18 years ago
I also get up to 55gr of IMR 4895 when reloading 06 with my 650 and large powder bar. In: Loading for 30-06
18 years ago
It depends on the powder being used, and the bullet weight. With ball/spherical powders, or short-gr …In: Loading for 30-06
18 years ago
I just got my XL650 set up which I intend to use for loading 30-06. I was a bit disappointed t …In: Loading for 30-06
18 years ago
David -
Dillon's short list is correct. Having sold another brand and type of press to buy a 5 …In: Minimum gear for getting started...
18 years ago
Under specs and caliber changes, You will also need (at minimum): Die set (included with t …In: Minimum gear for getting started...
18 years ago
Hi, I'm interested in the 550/550B for 40S&W. Is there a checklist somewhere for what I w …In: Minimum gear for getting started...
18 years ago
No. The Square Deal B cannot load bottleneck cartridges such as 357 SIG. I suggest you consider th …In: brand new
18 years ago
im looking at getting into reloading 9mm and 357 sig woulf this be a good reloading machine for me? …In: brand new
18 years ago
18 years ago
http://thomas.loc.gov/cgi-bin/bdquery/D?d110:1:./temp/~bdlln0::In: HR 96-Require Background Checks at Gun Shows
18 years ago
My first guess is that the shellplate bolt has tightened. Does the shellplate rotate easily by hand …In: Stiff operation on xl650
18 years ago
The operation of my new XL650 has just become very stiff all of a sudden, does anyone here have any …In: Stiff operation on xl650
18 years ago
New Dillon owner. From reading it appears Ball and Stick powders dispense more accura …In: Stick powders
18 years ago
18 years ago
Just ordered a 650 and should be here in a couple of days and have a ? about powders in the d …In: Stick powders
18 years ago
I had the same problem with "Remmington" primers on my 650XL and adjusting the shell plate …In: primers not in line with case
18 years ago
I have found it's easier to Size/Deprime and trim the brass first using a seperate tool head. N …In: primers not in line with case
18 years ago
Thank you Anm2 man for the info on the primer station locater tab adjustm …In: primers not in line with case
18 years ago
Yourmaker You may want to check the adjustment on the Primer Station locator Tab. There is a …In: primers not in line with case
18 years ago
so far most primers seat well. although once in awhile some do not, have to turn brass a little then …In: primers not in line with case
18 years ago
Please keep us updated on this. I am having similar problems with my 650 while loading .45 ACP usin …In: primers not in line with case
18 years ago
Thank you dillon for your help with this primer problem. I have backed up the shell plate bolt …In: primers not in line with case
18 years ago
Are you by any chance using military cases with crimped in primers? These will cause hard prim …In: primers not in line with case
18 years ago
The shellplate bolt should be very close to tight;we suggest tightening it until it stops, then back …In: primers not in line with case
18 years ago
Thanks Randy, I tried as you said about the shell plate. It did work better. Primers do seat better, …In: primers not in line with case
18 years ago
Dale, Make sure the shellplate isn't too tight. I had that happen last night and the shellp …In: primers not in line with case
18 years ago
I just started loading 38 special for the first time on this new xL650. I love this machine, only I …In: primers not in line with case
18 years ago
I've used mine for years without the auto casefeeder. If you wanna increase your empty brass ca …In: 650 without case feeder
18 years ago
I just started using the 650 without feeder. I just drop them in tube and go.In: 650 without case feeder
18 years ago
does anyone use the 650 without the case feeder... I just purchased it and was wondering prope …In: 650 without case feeder
18 years ago
First, I suggest you clan up the machine, and lube the shaft with 30 wt motor oil. If …In: 308 on a 450
18 years ago
Please forgive a stupid question. I used to shoot competition handgun about 20 years ago using my 45 …In: 308 on a 450
18 years ago
? If you are looking for replacement parts, they aren't available online yet. Please order by …In: Replacement Parts
18 years ago
18 years ago