Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
I can see listed in the manual the screws you are pointing out (14013). However, they are not label …In: Inconsistent Primer Seating
8 years ago
Check the two small bolts that secure the roller bracket to the underside of the machine platform. I …In: Inconsistent Primer Seating
8 years ago
No doubt this issue has been discussed before, but I can find no mention of it. Recently, I have no …In: Inconsistent Primer Seating
8 years ago
7 years ago
Anyone who thinks a Hornady is better, just try one. I got an LNL as match product and couldn't …In: Unconcisted powder drop
8 years ago
My experience with Dillon powder hoppers on a 1986 550 and a 2001 SD, is they throw +/-.1 grains for …In: Unconcisted powder drop
8 years ago
Come on Dillon and cut the crap.
1: I don´t have a response from you in my mail at all (not in inbo …In: Unconcisted powder drop
8 years ago
Please check your spam filter for our response. The bellcrank cube , #13871 has fallen off of your p …In: Unconcisted powder drop
8 years ago
Thanks for the tip LeftyTSGC.
I have tried several different methods. Fill the hopper almost full a …In: Unconcisted powder drop
8 years ago
It may be the "tap" on the top stroke that is causing it. If you set everything up from a …In: Unconcisted powder drop
8 years ago
Just to be sure, do you know for 100% that you have the "SMALL" powder bar installed and n …In: Unconcisted powder drop
8 years ago
Just to be sure, do you know for 100% that you have the "SMALL" powder bar installed and …In: Unconcisted powder drop
8 years ago
Do not use a rubber band, spring,etc; to retract the powder bar. It sounds like the failsafe rod is …In: Unconcisted powder drop
8 years ago
I have done some more testing. I removed the spring on powder bar lever so it doesnt lock on the edg …In: Unconcisted powder drop
8 years ago
I have done some more testing and tinkering with the machine after i have found some tips on other f …In: Unconcisted powder drop
8 years ago
I have already written that, but here it comes again!!!!!!!!!!!!!!!!!!!!!!!!
Powder 1 inch from top …In: Unconcisted powder drop
8 years ago
How much powder is in the hopper? Be sure to start with the hopper at least 2/3 full. Throw 10-15 ch …In: Unconcisted powder drop
8 years ago
I have tried different speed. No difference.
When the rod is in end stroke down, waited for 7-10 sec …In: Unconcisted powder drop
8 years ago
Some powders are known for causing trouble. Usually that is a stick powder. Some people have troub …In: Unconcisted powder drop
8 years ago
• The Dillon powder measure hopper has in integral baffle molded into it. Start with the hopper at l …In: Unconcisted powder drop
8 years ago
If you are experiencing inconsistent powder throws from you Dillon Powder Measure you can call us at …In: Unconcisted powder drop
8 years ago
Hello.
I just got my new SDB and it started with problems on my first reloading session.
The proble …In: Unconcisted powder drop
8 years ago
8 years ago
Hello.
I just got my new SDB and it started with problems on my first reloading session.
The proble …In: Unconsisted powder drop
8 years ago
I have now the need to set up a toolhead with all the dies and powder dispenser for reloading 45-70. …In: What dies for 45-70
8 years ago
8 years ago
We have no plans to offer carbide 6.5 Creedmoor dies at this time, but that could change eventually.In: 6.5 Creedmoor
8 years ago
Might anyone have any idea if or when Dillon might or will be coming out with a three Die Carbide se …In: 6.5 Creedmoor
8 years ago
First, check the primer seating assembly and be sure that it is threaded fully up into the underside …In: Flippin Primers
8 years ago
Have a 550b, Every 100 rounds its flipping three primers. What adjustment do i need to make, it make …In: Flippin Primers
8 years ago
Ok, called Dillon and they recommended that I do the following:
1. Tap on PM with knucke to settle …In: belled case powder drops
8 years ago
Plus or minus .10 grain is normal for most powder measures and I've always found the Dillon mea …In: belled case powder drops
8 years ago
I have checked case diameter prior to belling and after and avg 0.18 greater with seated bullet. I …In: belled case powder drops
8 years ago
Sounds like you are belling the case to much. You should not be going more than 20 thousandths large …In: belled case powder drops
8 years ago
In case it matters, I am using small powder bar for loading approx 4.2/4.3gr of Winchester 231 in 9m …In: belled case powder drops
8 years ago
I am seeing differing results when dropping powder on a belled vs non belled case anywhere from 0.06 …In: belled case powder drops
8 years ago
Please send a couple of photos and your address to sales@dillonprecision.comIn: Sdb power measure bent
8 years ago
Hi yes i have gotten a used sdb and a 650 lil while ago and been cleaning them up and fixing any br …In: Sdb power measure bent
8 years ago
We never sold the GSI bullet feeder. Our understanding is that GSI is not selling this product at th …In: Bullet dropper
8 years ago
Any there any chance you still have your GSI bullet feeder thay you posted about long ago?In: Bullet dropper
8 years ago
We don't carry the microswitch that Mr. Bulletfeeder uses.
contact sales@cedhk.com , the US im …In: Bullet dropper
8 years ago
I just switched to 223 from pistol rounds. I have complete tool heads including bullet droppers for …In: Bullet dropper
8 years ago
8 years ago
Does anyone know the color Dillon uses for 45 acp? The one I have has a red case bushing, having tro …In: Shell case bushing
8 years ago
Piece of cake - installed and works fine. Mystified as to where the original went - but thanks.In: Powder bar travels too far forward
8 years ago
It sounds like you are missing the bellcrank cube. This is a white delrin square that fits over this …In: Powder bar travels too far forward
8 years ago