Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
8 years ago
I believe the RL550 was the first Gen in 1985. What about subsequent models? Made from when to when, …In: 550 Generations
8 years ago
Any suggestions for drying reloaded 45LC cartridges after discovering cases were wet? I disassemble …In: Wet cases reloaded
8 years ago
Remove the "E" clip and drop out the decapping pin. Then everything will run as normal.
JJIn: reloading primed 9mm
8 years ago
I recently acquired over 1000 primed 9mm brass cases that were not sized. What do I need to do to r …In: reloading primed 9mm
8 years ago
Is the index alignment tool different than the alignment tool that gets dropped into the powder funn …In: Primers hitting shell plate on upstroke
8 years ago
Please email us at sales@dillonprecision.com , request a 650 index alignment tool. Please include yo …In: Primers hitting shell plate on upstroke
8 years ago
Remove the shell plate and clean the underside of it along with the part below it where the ball/spr …In: Primers hitting shell plate on upstroke
8 years ago
Im having a problem with flipped primers on the 650. Running the press without brass I can actually …In: Primers hitting shell plate on upstroke
8 years ago
8 years ago
Please send us an email requesting a replacement small primer slide assembly. Include your address.In: Primer slide wearing out?
8 years ago
The shim looks ok. The paint is starting to rub off towards the back. I think I’m on my third or fou …In: Primer slide wearing out?
8 years ago
As jforwel said, inspect the primer slide shim. Please email us, let us know what is worn, and inclu …In: Primer slide wearing out?
8 years ago
The black plate under the primer bar I believe is called a slide bearing. Anyway, take a look at it …In: Primer slide wearing out?
8 years ago
My small primer cup started hitting the right side of the aluminum housing on the before it reached …In: Primer slide wearing out?
8 years ago
I think there just old and I guess wore out.... they have dropped thousands upon thousands of charge …In: New 650
8 years ago
Call Dillon there is a conversion kit. There is a number for the kit somewhere in the forums, but w …In: New 650
8 years ago
Well I bought a new xl650 in 30-06.
What a beautiful press.
Works flawlessly makes very good quali …In: New 650
8 years ago
Another possibility is that your case mouths are not trimmed square at the factory. This is uncommon …In: Non concentric "flare" or bell at station 2
8 years ago
It sounds like the shells are not flat on the top or maybe the powder funnel has worn uneven. I wou …In: Non concentric "flare" or bell at station 2
8 years ago
Hello
After "flaring" the mouth of 45 ACP rounds at station 2, I have observed that the s …In: Non concentric "flare" or bell at station 2
8 years ago
we are within a day or so on responding to email. Please resend it to gary.kieft@dillonprecision.com …In: No BS Warranty??
8 years ago
RL550B purchased in 2001.
Well I guess the NO BS warranty doesn’t apply anymore!?!? I’ve had two ma …In: No BS Warranty??
8 years ago
It sounds like the shellplate bolt is slightly loose. To verify, push down on the edge of the shellp …In: Casing notches
8 years ago
My 550B occasionally puts a notch in the casing at station two on 9 mm only. I loaded 200 casings to …In: Casing notches
8 years ago
Photos received. Push the white case feed adapter down until it is fully contacting the top of the …In: .223/5.56 NATO Hanging Up on Case Feed Arm Bushing
8 years ago
It was in 9mm originally. I will shoot some photos this week. Thank you for the reply.In: .223/5.56 NATO Hanging Up on Case Feed Arm Bushing
8 years ago
Was the machine previously in a different caliber, or always in 223? Can you send some photos to sal …In: .223/5.56 NATO Hanging Up on Case Feed Arm Bushing
8 years ago
About 50% of the cases stop on the edge of the CF arm bushing (green #13412) and do not drop into po …In: .223/5.56 NATO Hanging Up on Case Feed Arm Bushing
8 years ago
New 1050 with the updated casefeeder. Noticed what I would call excessive heat around motor/gearbox, …In: Casefeed motor HOT?
8 years ago
The current version of the D-Terminator scale is designed to allow trickling. As in the instructions …In: question regarding D-Terminator Electronic Scale usage
8 years ago
completed my question in a reply...didn't see a way to edit the post.In: question regarding D-Terminator Electronic Scale usage
8 years ago
...opps.
I just picked up the D-Terminator Electronic Scale and not sure if its my usage or if the …In: question regarding D-Terminator Electronic Scale usage
8 years ago
[full disclosure: new to reloading]
I picked up the D-TerIn: question regarding D-Terminator Electronic Scale usage
8 years ago
Back up your crimp slightly. That is a bit too much, which can cause the case below the crimp to bul …In: Buldged cases
8 years ago
Thanks and after the crimp it measures .375 and I did try to put the cardrige in the case guage rim …In: Buldged cases
8 years ago
This part of the forum is for Mr. Bulletfeeder Setup questions.
To answer your question, you probab …In: Buldged cases
8 years ago
I have a 550C/9mm(Dillon Dies)/Missouri Coated 124glrn bullets and not all rounds pass the case gaug …In: Buldged cases
8 years ago
Same issue here, had to bend the chute and then grind a curve in it to fit around the shell plate. …In: Loaded Cartridge Chute Issues
5 years ago
Same issue here. I bought the strong mount a while ago, put it all together but never used it. I j …In: Loaded Cartridge Chute Issues
5 years ago
Have the exact same issue with one I just received last week. Went to mount it and the press is fin …In: Loaded Cartridge Chute Issues
6 years ago
I ran into the same issue with a 550C purchased in October '18. Called Dillon but wasn't …In: Loaded Cartridge Chute Issues
7 years ago
Please send some photos to sales@dillonprecision.com
Include your address in case we need to send y …In: Loaded Cartridge Chute Issues
8 years ago
I have an RL550B that's nearly 20 years old. I think I bought it in 2001. Several years after b …In: Loaded Cartridge Chute Issues
8 years ago