Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
The shim I described above is called the primer track bearing Dillon part # 14015. TBIn: Primer Slide Issues
17 years ago
For the last few months I have been having issues with the primer slide sticking and not always pick …In: Primer Slide Issues
17 years ago
No significant problems loading 4064 into a .308 cartridge. Even with the extruded powder, chare wei …In: Loading with IMR4064
17 years ago
I'm going to be loading .308 and am wondering if i'm going to have issues with the dillon …In: Loading with IMR4064
17 years ago
It is not uncommon for the security tape to break during shipment.In: Received Shipment - Have Question
17 years ago
Dillon, Should I be concerned that the security label was cut then? Is it possible that happe …In: Received Shipment - Have Question
17 years ago
We don't "pre-adjust" the dies in the box. Just lucky as to how far the lock ri …In: Received Shipment - Have Question
17 years ago
Hello Dillon, Received my latest shipment today - dies, etc. to reload 7mm Rem Mag and 30-06 on my …In: Received Shipment - Have Question
17 years ago
no problem. adjust the cam pin down so that when the handle is being pushed forward and a case is in …In: case insert slide not pushing shell in
17 years ago
I appolgise to dillion precision, and thier workers, the case was pushed in   …In: case insert slide not pushing shell in
17 years ago
Ive ordered the xl650 in 44 special/44 mag.. the number 9 camming pin is too long or th …In: case insert slide not pushing shell in
17 years ago
You need to look at a in-expensive LEE single stage press. I bought one for Midway for just th …In: lee adapter for 550
16 years ago
This unit requires a smaller diameter shaft cut for a lee type shellholder to push the bullet …In: lee adapter for 550
17 years ago
I bought lee cast bullet sizing dies. What do I need to mount the ram to the sheel plate. Im guess …In: lee adapter for 550
17 years ago
First post here... My 650 is an early one, and I think they had the case feed a bit higher back th …In: Case Feed Lowering
17 years ago
Thanks so much for the ideas. I was not sure if it should be done, but since this is the first …In: Case Feed Lowering
17 years ago
Two bolts 2 5/8s . Bottom Pipe 8 Middle Pipe 6 1/4 Top Pipe 9 Bottom of tube has straight joint fitt …In: Case Feed Lowering
17 years ago
17 years ago
Could you email me the detailed pictures of that.. Its kinda hard to tell exactly what you done, and …In: Case Feed Lowering
17 years ago
17 years ago
Yes I lowered my xl650 case feed. I have pictures that are too bit to upload (2mb each). …In: Case Feed Lowering
17 years ago
I am wondering if anyone has lowered the case feed assembly. I am installing this unit in my 5 …In: Case Feed Lowering
17 years ago
Either the cube is cracked, or else the nylock nut that goes onto the bellcrank bolt needs to be tig …In: White Cube on powder measure pops off!
17 years ago
Ok this is kinda weird, the "White Cube" on the powder measure pops off when the handle is …In: White Cube on powder measure pops off!
17 years ago
Spacers would cause other problems. Check the shellplate bolt, make sure it is as tight as you can r …In: seating primers
17 years ago
I hqve a 550b .Just bought it used.It is in great shape. I seem to have an issues seating the primer …In: seating primers
17 years ago
I have a older model D-Teminator That takes a single 9 volt battery .Are the calibration instru …In: Dillon D Terminator
17 years ago
The case feeder should run 38 Spls with the washer installed. It is not necessary, but should …In: Shell Plate
17 years ago
Hi I have a case feeder set up for 357 ...meaning the spacer washer is installed . I am going to loa …In: Shell Plate
17 years ago
The RL1050 has a different linkage and a shorter stroke, .223 Rem is the tallest cartridge that can …In: RL1050
17 years ago
17 years ago
We carry Redding dies for 7.62 x 39mm, stock#12045-$54.95. They are currently out of stock, but more …In: 7.62x39
17 years ago
How long will it be until I can get the dies for 7.62x39 for my 550B? And should I be on a list?In: 7.62x39
17 years ago
Not had any other problems with this . Never thought of the old primer not popping out. I I'll …In: Primers ..Bulge
17 years ago
I'm no reloading pro but I think what is happening is that you are not completely punching out …In: Primers ..Bulge
17 years ago
17 years ago
After checking the old posts I can't seem to find anything specific to this problem . When I ru …In: Primers ..Bulge
17 years ago
All you have to do it remove the decapping pin from the case sizing and decapping dye. Then you can …In: Depriming Live Primers
8 years ago
I would suggest expending the primer in a firearm. Then resize and decap as usual. At .04 cents ti …In: Depriming Live Primers
10 years ago
Don't assume WD40 will kill primers. A few years back I filled 6 primed 38 spl cases with WD40 …In: Depriming Live Primers
10 years ago
I have been reloading for about 10 years now and I deprime live primers on occasion. It is risky bu …In: Depriming Live Primers
10 years ago
Don't do i! If you want to reuse the shell then fire the primed cartridges in your gun (like s …In: Depriming Live Primers
15 years ago
WD-40 will "desensitize" primers, after 48-72 hours of immersion, it will not permanently …In: Depriming Live Primers
15 years ago
Good topic for a newbie like myself to read. I like the idea of WD40 killing the primers and then de …In: Depriming Live Primers
15 years ago