Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
13 years ago
I used a Dillon sizing/decapping die and a vibratory cleaner. Do the cases need to be lubed …In: Removing Case Lube?
13 years ago
I used a Dillon sizing/decapping die and a vibratory cleaner. Do the cases need to be lubed …In: Removing Case Lube?
13 years ago
If the bullet is pushed back into the case, then either the bullet diameter is too small, or the exp …In: Removing Case Lube?
13 years ago
When I tumbled my .223 to remove the lube, I had several cartridges destroyed in the tumbler. The cr …In: Removing Case Lube?
13 years ago
I reload 5.56 ammo with a 550, your case lube works really great. Zero Stuck-case issue. I also remo …In: Removing Case Lube?
15 years ago
Thanks, I'll get another batch of media and use your method!! I appreciate your help!In: Removing Case Lube?
16 years ago
The case lube must be removed from ammunition before firing it. Failure to do so prevents the cases …In: Removing Case Lube?
16 years ago
One thing I have not seen addressed is how is case lube removed after the cartridge is loaded, or is …In: Removing Case Lube?
16 years ago
The manual is available online, in a PDF-file, or phone or e-mail your address and we can mail a pap …In: starting back reloading
17 years ago
I bought a 650 along with some case prep accessories more than 14 years ag …In: starting back reloading
17 years ago
Redding now offers a push-through size die to size the overexpanded base of cases fired in unsupport …In: 550B & Glocked Brass
17 years ago
Boy i can't remember but i think it was lee or rcbs that makes a die to get the bulge out of gl …In: 550B & Glocked Brass
17 years ago
I have had the same problem with my Dillon pistol sizing dies. I use a Lee Carbide Factory Cri …In: 550B & Glocked Brass
17 years ago
I just ordered a Redding GRX size die, to full size the .40cases. $33.00. Just another step to reloa …In: 550B & Glocked Brass
17 years ago
I’m having trouble with posting in the form. I have a 550B and loading for .40 S&am …In: 550B & Glocked Brass
17 years ago
17 years ago
Guys, check out the forums at barretrifles.com or iboats.com and please ditch this software. T …In: Forum Software - UPGRADE PLEASE?
17 years ago
We realistically expect it to be ready in the next two to six months. Designing is completed, …In: 50BMG Press?????
17 years ago
I have heard that Dillon has developed a press for the 50BMG round. I have a 50BMG rifle but c …In: 50BMG Press?????
17 years ago
17 years ago
Is the Redding .30 Carbine Crimp die that is sold under "crimp dies" section a Taper crimp …In: Redding 30 Carbine Crimp die
17 years ago
8 years ago
8 years ago
8 years ago
Please exit quickly, and do not allow the door to hit your backside.
And thank you for your 40 y …In: NRA
10 years ago
Please exit quickly, and do not allow the door to hit your backside.
And thank you for your 40 y …In: NRA
10 years ago
10 years ago
17 years ago
I have just given up my membership to the nra. I was a member for 40 years and a life member for 30 …In: NRA
17 years ago
I might be wrong here.. but, the RCBS flashole debur tool does not come preset for a 223rem. …In: Flash hole deburring question
17 years ago
I have a question regarding deburring cartridge flash holes in new brass cartridges. Simply put, how …In: Flash hole deburring question
17 years ago
If it's none of the problems above as others have stated , be sure to check your load data / po …In: Reloading .223 Rem and having extractor problems.....
6 years ago
It could also be a problem with a rough chamber, especially if the weapon is new. Chrome lined …In: Reloading .223 Rem and having extractor problems.....
17 years ago
Hugo, I just submitted a 'rather large article' about reloading for .223-AR's. I woul …In: Reloading .223 Rem and having extractor problems.....
17 years ago
In getting 'stuck ' is the extractor just not picking up or do you have to punch out the c …In: Reloading .223 Rem and having extractor problems.....
17 years ago
I'll try turning down the sizer die a bit more. I don't think it could really get any clos …In: Reloading .223 Rem and having extractor problems.....
17 years ago
Be sure sized cases drop in flush with the lower step on the case gage. It may be necessary to turn …In: Reloading .223 Rem and having extractor problems.....
17 years ago
You may need to screw down the sizer die a little more, just where it cams over a bit on the full st …In: Reloading .223 Rem and having extractor problems.....
17 years ago
I am using the XL650 to reload .223 Rem using CCI primers, W748 powder, and 55gr HPBT. I am reloadin …In: Reloading .223 Rem and having extractor problems.....
17 years ago
I had a similar problem with 223 brass from 4 different manufacturers. Even with the pockets s …In: Primer frusteration. About to get really mad.
16 years ago
I had the same probleme using Federal primers while reloading 9mm (either with my 650 or my Lee turr …In: Primer frusteration. About to get really mad.
17 years ago
For priming problems, I strongly suggest you phone us when you can be in front of the machine …In: Primer frusteration. About to get really mad.
17 years ago
I am having the same problem with 38spl, using Federal primers, I would say check your brass but you …In: Primer frusteration. About to get really mad.
17 years ago
I've had my 650 for about 6 months and have the same problem. In fact I have "popped" …In: Primer frusteration. About to get really mad.
17 years ago
The shell plate shouldn't be tight. When installing the shell plate, tighten the bolt unt …In: Primer frusteration. About to get really mad.
17 years ago
what happens if you take one of the shells you finally got the primer in, fire it, deprime it, and t …In: Primer frusteration. About to get really mad.
17 years ago
Uhhh, maybe a dumb question but have you removed the primer pocket crimp before attempting to reload …In: Primer frusteration. About to get really mad.
17 years ago