Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
I suspect both a magnetic field from the tumbler motor and the vibrations are the cause of you …In: Dillon Scale
19 years ago
Well fall is comming up so I thought I better start making a list of supplies and I pulled out …In: Dillon Scale
19 years ago
Sir, if you locate the primer indexing arm - it's between primer body housing and at the bottom …In: Casefeeder
19 years ago
If you need to index your primer disc to get a primer ready to rock n load . look between powder fai …In: Casefeeder
19 years ago
What we do here is to manually index the primer disc by pushing the primer index arm with a th …In: Casefeeder
19 years ago
Hello, If you have cases in the casefeeder, cases are ready to go. Now add the primers. Is there a …In: Casefeeder
19 years ago
Some individual parts, such as caliber conversion parts for the Square Deal B, RL550B and XL65 …In: individual parts
19 years ago
Just finished loading 2000 rds of .45 ACP and only had two primers and one anvil on the floor. The f …In: spent primmers
18 years ago
Truthfully I don't think their is any answer to this problem. I don't see the point in cha …In: spent primmers
18 years ago
I've owned a 550 for 14 yrs and been dropping spent primers all over the garage floor for 7 or …In: spent primmers
18 years ago
I had the same problem and the hardened pins were of little help. This took care of the problem almo …In: spent primmers
18 years ago
I have the same problem, makes for a big mess. The last time I reloaded 3500 rounds, well …In: spent primmers
19 years ago
My primer catcher is opening and closing perfectly with the original cotter pin, still sending spent …In: spent primmers
19 years ago
I had the same problem but solved it by making sure the cotter pin was bent flush with the spe …In: spent primmers
19 years ago
I have replaced the standard cotter key with a standard sewing Pin - bent at a 60 degree …In: spent primmers
19 years ago
I always used needle bearing from an automotive u-joint for decapping pins for my RCBS and Pacific d …In: spent primmers
19 years ago
I replaced the cotter key with a spare RCBS decapping pin, works ok and surprisingly doesn't wa …In: spent primmers
19 years ago
Instead of a safety pin, when I had my 550 I used a small finishing nail cut to length and with the …In: spent primmers
19 years ago
The most likely cause for this is the aluminum cotter key that the spent primer catcher pivots …In: spent primmers
19 years ago
19 years ago
I have the 55b also but no case feeder. The primers do the same thing, more so CCI than any ot …In: spent primmers
19 years ago
I have the 550b with the auto case feeder. right now about 80% of the spent primmers go into the sma …In: spent primmers
19 years ago
I wouldn't; those clear tubes are a bitch to clean. Ever considered carbide dies? Yeah they …In: 650 Casefeeder
18 years ago
I have cleaned my case feed tube with simple green , old piece of wash cloth over 1/2 inch dow …In: 650 Casefeeder
19 years ago
If you are using the Dillon Case Lube, the actual lube is Lanolin. The same oil that waterproo …In: 650 Casefeeder
19 years ago
Dillon case lube won't adversely affect the plastic. The alcohol carrier won't damag …In: 650 Casefeeder
19 years ago
Hello, Does anyone know if it is ok to leave cases in the case feeder with lube on them? No …In: 650 Casefeeder
19 years ago
I wish I did start with the 650 but having the 550b only 6 months and all the quick change pistol se …In: 30 carbine
19 years ago
I use to load both .30 Carbine and .223 on my 550b but after a while I really wanted the ease of a c …In: 30 carbine
19 years ago
19 years ago
With all the new carbines released and sold by CMP, would it not be profitable to modify the Dillon …In: 30 carbine
19 years ago
The 30 Carbine case is too skinny and tall to reliably work through the 550 Casefeeder. We tri …In: 30 carbine
19 years ago
I was reading somewhere that the 30 carbine, is the 22nd most reloaded cartridge. Why doesn't D …In: 30 carbine
19 years ago
7 years ago
We make a 550 shell plate for 5.7x28 if anyone is interested. Lisa lisa@eliteammunition.c …In: FN 5.7x28?
17 years ago
Clay, I have purchased Redding FN 5.7x28 reloading dies. I had a master machinist, and I …In: FN 5.7x28?
19 years ago
The 5.7x28FN cartridge has too small of a rim diameter to work on any Dillon progressive loaders. It …In: FN 5.7x28?
19 years ago
Any plans in the works for a XL650 caliber conversion kit for 5.7x28? (FN PS90, etc.) I know …In: FN 5.7x28?
19 years ago
I also noticed the newer style powder measures the powder hopper is removable, held in place with 2 …In: First Time setup 550B
19 years ago
The change was initiated with the introduction of the SL900 shotshell loader. The purpose is t …In: First Time setup 550B
19 years ago
I've got one of the classic 550's with the spring return. It's wonderful! …In: First Time setup 550B
19 years ago
19 years ago
Hey Dillon, Thanks so much for the reply. I had a feeling the spring was no longer used as the m …In: First Time setup 550B
19 years ago
For the last six or seven years, the powder measures have not used any return springs to pull …In: First Time setup 550B
19 years ago
Finished setting up my work bench and then the Dillon 550B over this weekend. Patience is key and …In: First Time setup 550B
19 years ago
The D-Terminator scale is made for us by CED in Hong Kong. We have been dealing with them for …In: Why Buy a D-Terminator?
19 years ago
I just returned my second RCBS 750 electronic scale and have been looking at the D-Terminator. The f …In: Why Buy a D-Terminator?
19 years ago