Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
16 years ago
Please send me some sample cases. Mark them attention :Gary Then we can check it out.In: 327 Fed Mag deprime pin
16 years ago
The rod measures 2.627" with the pin retainer collar removed (the smoothe one). I am guessing a …In: 327 Fed Mag deprime pin
16 years ago
We haven't had any other complaints. See if the smooth retaining nut is fully threaded onto the …In: 327 Fed Mag deprime pin
16 years ago
It is smooth, and fits inside the case fine. That's not the problem. The whole spri …In: 327 Fed Mag deprime pin
16 years ago
First, be sure it is the decapping pin and not the nut that holds it in place. We don't offer a …In: 327 Fed Mag deprime pin
16 years ago
Not a pin problem, but the sprint loaded rod is too long. Took me awhile to figure this out, t …In: 327 Fed Mag deprime pin
16 years ago
Case stuck in my sizing die (first time ever), and a saw it was the depriming pin stuck in the flash …In: 327 Fed Mag deprime pin
16 years ago
It's covered under warranty. Phone or e-mail us, and please include your address information. W …In: Frame Breakage
16 years ago
My machine was bought in 1992 and the frame Part # 13445 broke in half right behind the back bolt ho …In: Frame Breakage
16 years ago
i use a customized sako hunting rifle with an 30 inch barrel an gain twist (lothar walter barrel) .
…In: .338 Lapua Mag
14 years ago
I would recomend neck sizing cause its a huge cartridge . i m not sure full resizing would work prop …In: .338 Lapua Mag
14 years ago
I am about to the same thing with a 550. Is there anything you can pass on from your experienc …In: .338 Lapua Mag
15 years ago
I cannot tell you anything yet. All I have done is read. HOWEVER, I have been on Long Range Hunting …In: .338 Lapua Mag
16 years ago
Just purchased the necessaries (Caliber conversion kit, etc) to load .338 Lapua Mag using my 550B. …In: .338 Lapua Mag
16 years ago
One last thing regarding Irpnrider's suggestion: I called Ruger and was told that under no cir …In: .44-40 ruger vaquero reload probs
13 years ago
Thank you, my un-met friend. Followed your advice and I am now blazing away with my (until now) bar …In: .44-40 ruger vaquero reload probs
13 years ago
When I load 32-20, 38-40 and 44-40 cartridges for revolvers the bullets will fit a gage or rifle cha …In: .44-40 ruger vaquero reload probs
15 years ago
I believe Ruger might do it for you no charge. It's been a number of years since I got my 2 44- …In: .44-40 ruger vaquero reload probs
16 years ago
Thanks for the response. My cast resized bullets mic at .428. I slugged the cone in a ch …In: .44-40 ruger vaquero reload probs
16 years ago
What bullet diamter are you loading? The early Vaqueros were cut at SAAMI minumum chamber specs, and …In: .44-40 ruger vaquero reload probs
16 years ago
Reload .44-40, 220 gr cast bullet, slugged barrel to get diameter right during resizing of my cast b …In: .44-40 ruger vaquero reload probs
16 years ago
16 years ago
How do we bring an old (past) topic up to the front for all to view. for an example there's a t …In: View past Topics
16 years ago
Actually, removing the size die is very easy. Detach the return rod on the powder measure, rem …In: 9mm brass sized and primed
16 years ago
Hi, i just purchased a SDB in 9mm and was wondering how I should start as I have 2,000 pcs. of …In: 9mm brass sized and primed
16 years ago
16 years ago
Ok switched to the large powder bar for the first time and its all now within .1 tenth of a grain. J …In: Help- Powder Measurer
16 years ago
I would move to the large powder bar. A longer cylinder will meter better than a wide/flat cyl …In: Help- Powder Measurer
16 years ago
I have just gotten my 550b, First progressive press and have loaded a few hundred rounds of 10mm and …In: Help- Powder Measurer
16 years ago
I think Dillon gave the best advise. Check your cases in a case gauge. Then adjustments to loa …In: Case Bulge
16 years ago
Hi- Thanks for your response. As it turned out, backing the seating die off two full turns is …In: Case Bulge
16 years ago
First, size several cases, check these cases in the gage-sized only, no flaring, no bullet seat. Wha …In: Case Bulge
16 years ago
I have case bulge at the bottom of my finished 9mm rounds that prevent them from fully dropping into …In: Case Bulge
16 years ago
Thanks cnozumi your post got me looking in the right direction. I'm not a perfect relo …In: 550 B jaming
16 years ago
+1 on ietrooper. Tighten the brass-tipped set screw in the side of the shaft to prevent the shellpla …In: 550 B jaming
16 years ago
I have had my 550B for many years .... great machine! Some years back had a problem with multiple in …In: 550 B jaming
16 years ago
Not sure if this will fix the problem ...but it's worth a shot When you set the tensio …In: 550 B jaming
16 years ago
I have a 550b for a few years, however since my last move the shell plates tightness up after a few …In: 550 B jaming
16 years ago
I was having the same issue, I took a little off the detent ball spring and it solved the problem.In: Powder mess at station 3
16 years ago
Hi fpfiglia, to avoid the mess at station # 3 cut the index spring 1/3, and it will solve the proble …In: Powder mess at station 3
16 years ago
Thanks for the feedback, I'll give this a try. Already tried adjusting and re-adjusting the sh …In: Powder mess at station 3
16 years ago