Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
I had a similar problem and found that the shellplate bolt had backed out a bit. After retightening. …In: Depriming Problem
16 years ago
It sounds like the spent primer is sticking on the end of the decapping pin and getting partially pu …In: Depriming Problem
16 years ago
Sometimes the resizing die fails to remove the spent primer. It's beginning to happen mor …In: Depriming Problem
16 years ago
Add two used fabric sheets to your tumbler with every load of brass. I have been using the same medi …In: Cleaning Brass after tumbling
16 years ago
After I resize my brass, I take a bath towel, place about 50 brass on it, squirt some lighter f …In: Cleaning Brass after tumbling
16 years ago
16 years ago
I have just gotten back into reloading and have another new XL650 on order. After tumbling my brass …In: Cleaning Brass after tumbling
16 years ago
I found it very difficult to tell the difference until I deprimed. Then it shows as a ring of metal …In: Identifying military rifle brass
13 years ago
Travis, The FC, LC brass is most definately crimped. PMC will be if it was made IAW military s …In: Identifying military rifle brass
16 years ago
A good rule of thumb is that any brass that lacks a cartridge marking, but only has a two or three l …In: Identifying military rifle brass
16 years ago
I know that military brass has a crimp on the primer that needs to be removed. The question that i h …In: Identifying military rifle brass
16 years ago
I partially disassemble the case feed-remove the right front mounting bolt, loosen the right rear bo …In: 550 case feeder
16 years ago
Installed a case feeder for my 550B. works great, no problems. Question is how do you ma …In: 550 case feeder
16 years ago
Quote:
Originally Posted by http://www.starlinebrass.com/faqs.ph...84eafb48ae8bd8
Why is it very …In: .45 cases stick to powder funnel
15 years ago
Starline has a fix for the expander. See there website under FAQ. Can not copy & paste the …In: .45 cases stick to powder funnel
15 years ago
I've just experienced this 'sticking' problem, but only with new brass. In my instanc …In: .45 cases stick to powder funnel
16 years ago
I load bunch of mixed brass, most have been reloaded at least 6-8 time and all my casings sticks in …In: .45 cases stick to powder funnel
16 years ago
Some sticking with new/once-fired brass is not unheard of. Wipe off the funnel with steel wool or a …In: .45 cases stick to powder funnel
16 years ago
Check your S&B brass with a magnet. There is a bunch in the country that is brass-plated steel c …In: .45 cases stick to powder funnel
16 years ago
As compared to other calibers I'm loading, some .45 ACP cases (greatest offenders being S&B …In: .45 cases stick to powder funnel
16 years ago
No truth at all. .223 is too tall to load on the SDB, as the cartridge is still partially in the sea …In: SDB in .223?
16 years ago
I'm hearing rumours that you can load .223 rifle cartidges in a SDB. Any truth to this? Where c …In: SDB in .223?
16 years ago
Just like me. I'm from the UK so Dillon reloading stuff isn't available here. It wou …In: New XL 650 on the way !
16 years ago
Walther Guy, I think you will be very pleased. What caliber are you reloading? Did you h …In: New XL 650 on the way !
16 years ago
I've got an XL650 and an SDB. My advice is to take your time, go over it slowly with the …In: New XL 650 on the way !
16 years ago
Get cases...lots of cases
Clean cases.... lots of cases
reload cases...lots of cases
got to the r …In: New XL 650 on the way !
16 years ago
1) Follow the directions, and 2) Make sure the bench does not rock especially front to back. I …In: New XL 650 on the way !
16 years ago
16 years ago
16 years ago
16 years ago
Hey Everybody, First post here...looks like a great place to hang my coat. I just order my …In: New XL 650 on the way !
16 years ago
No. The rim on 45AR is too thick. We tested it, and in 4 to 8 cycles cases broke out the top of the …In: .45 auto rim
16 years ago
Does Dillon offer a shell plate which will work with .45 auto rim? I shoot a s&w 625 revolver an …In: .45 auto rim
16 years ago
I had a problem like this and finally figured out the shell plate was being hung up by the edge …In: 650 Ram Jam
16 years ago
Hey! I wasn't blaming anything on you guys, I just thought that others users may try to help ou …In: 650 Ram Jam
16 years ago
So was loose powder interfereing with the shellplate action? BTW, we check this forum daily, but for …In: 650 Ram Jam
16 years ago
I thought this forum might be helpful, wrong! I figure if I can hypertune a Meade LXD75 10" SN …In: 650 Ram Jam
16 years ago
Hi Guys, I have been reloading for around 35 years using a single stage press (RCBS) but I a …In: 650 Ram Jam
16 years ago
Go with the 750. A fully loaded tumbler cleans better and faster than a partially filled one.In: 750 or 2001 tumbler??
16 years ago
I am about to place an order for my first tumbler. I plan on tumbling about 500 pcs at a time …In: 750 or 2001 tumbler??
16 years ago
Go to the thread on page 3 called "Ejector Wire." The last comment tells how to …In: Finished cartridge eject
16 years ago
You can use any die that you want. I like the Lee FCD for both the 9mm and 40 S&W ro …In: Finished cartridge eject
16 years ago
High folks, I just completed reloading my first test run on 9mm. The machine purrs like a kitten and …In: Finished cartridge eject
16 years ago