Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
It helps to lightly grease the underside of the shellplate bolt where it recesses down into the top …In: Variance in COAL
17 years ago
Powder measure measures good to .1. The shell plate is loose as all get out unlike my old one which …In: Variance in COAL
17 years ago
I have the same issues. Its fustrating. I had a 550b in 98/99 and it was dead on col -/+.001 avg. At …In: Variance in COAL
17 years ago
I am having the same problem. I've tried with preped case in #1 and without. Getting the same v …In: Variance in COAL
17 years ago
Dillon, Thanks for getting back to me. I will try another batch with a fired case in #1. …In: Variance in COAL
18 years ago
to maintain consistancy in the machine, you need to have a fired case in station one when the …In: Variance in COAL
18 years ago
I am not sure what happened but I'll try this again...I am new to rifle cartridge reloading and …In: Variance in COAL
18 years ago
In: Variance in COAL
18 years ago
No specific issues at all loading .308 on the RL550B. Just the usuals, having to lube the bras …In: .308 Loading (First timer)
18 years ago
I was referred by a friend to look at Dillon loaders since it's become cost-prohibitive to shoo …In: .308 Loading (First timer)
18 years ago
OUt here it is an off-the roll product. Try an automotive paint supply store, or a NAPA shop-both ca …In: Primer Problems
16 years ago
Where can you get the 1/8" automotive vacuum hose? I've tried a couple of auto parts …In: Primer Problems
16 years ago
17 years ago
This rubber hose is merely 1/8" automotive vacuum line. Go to any auto parts store, buy one foo …In: Primer Problems
17 years ago
So i found the problems with my 1050 and the primers...The rubber sleeve has cracked in half and fel …In: Primer Problems
17 years ago
Nextreme, Keep in mind that a commercial brand no longer ensures a non-crimped primer pocket …In: Primer Problems
17 years ago
I'm having the same problem with my 1050 doing 9mm, where I'm not having the problem with …In: Primer Problems
17 years ago
Does your primer pocket have sharp edges on the rim? If it does you will have to bevel the edge. I h …In: Primer Problems
17 years ago
Can you describe in detail what specifically is wrong with the mis-seated primers? What is the heads …In: Primer Problems
18 years ago
I have recently purchased a Super 1050 and I am very happy overall, however I have a lot of bad prim …In: Primer Problems
18 years ago
We don't have an electronic copy of the counter instructions, but phone or email us your addres …In: c100 counter
18 years ago
Would anybody have instructions or diagram to install a c100 counter on to a xl650. Than …In: c100 counter
18 years ago
An alternative, especially if you have reason to doubt the consistency of the resizing and belling, …In: Loading with primed brass
17 years ago
17 years ago
Actually, I would suggest removing the size die entirely, and just insert cases at station 1. This m …In: Loading with primed brass
18 years ago
I am new to progressive reloading and just purchased a 550. I have a few hundred 45ACP brass that ha …In: Loading with primed brass
18 years ago
Ya .223 and 5.56NATO are the same t for the case thickness. The 5.56 is thicker because of the …In: Die question .223 / 5.56x45
17 years ago
18 years ago
.223 remington dies are just fine for 5.56 NATO ammo. The primary difference in the two chambers is …In: Die question .223 / 5.56x45
18 years ago
I have brass from both .223 Remington and 5.56x45mm M193 Rounds. I can't seem to l …In: Die question .223 / 5.56x45
18 years ago
When I first received my 1200B Trimmer, it did not cut the cases square. After hours of tinkering, …In: 1200B Trimmer Not Cutting Square
18 years ago
no, sorry, wrong link correct one is: http://www.dillonprecision.com/shellplate_is_buckin …In: Redding seating dies for 9x21 caliber
18 years ago
Thank you for the answer, please, read http://www.dillonprecision.com/#/shellplate_is_buc …In: Redding seating dies for 9x21 caliber
18 years ago
The Redding 9x19 competition seat die will work fine for 9x21. It only has the one seating stem.In: Redding seating dies for 9x21 caliber
18 years ago
Hi, is the "Stock # 10671" (Redding Competition Pistol Seating Dies 9mm) good for s …In: Redding seating dies for 9x21 caliber
18 years ago
The most likely cause is the case feed bowl swaying. If your bench top is plywood, then reinfo …In: Problem with case feed system
18 years ago
I have a case feed system on my XL650 setup with the large pistol plate and loading .45 ACP. I' …In: Problem with case feed system
18 years ago
I just started doing just that , it works great. I hate case prep work and wish dillon would make a …In: Dillon case trimmer
14 years ago
I actually go one step further. I also de-cap and resize the cartridges in station 1 and have …In: Dillon case trimmer
18 years ago
Yes! The case trimmer mounts on the toolhead, at position #1. I bought a separate toolhead so as to …In: Dillon case trimmer
18 years ago
18 years ago
If I setup the case trimmer system on my XL650, will I be able to dump brass into my case feed syste …In: Dillon case trimmer
18 years ago
Thanks for the advice.
I just got this machine a few days ago and wow. I got the 1200B trimmer a …In: Powder Mess
18 years ago
Wipe off the funnel and powder measure with an anti-static dryer sheet. Next, when you drop powder …In: Powder Mess
18 years ago
A few little granuals of powder stick up in the powder measure after each charge. Then the movement …In: Powder Mess
18 years ago
I don't have any pics, but calipers should do the trick. Size a case and measure the diameter o …In: Expander/powder die adjustment?
18 years ago
Just bought an RL5550B and have been setting it up to reload 9mm. My question concerns proper adjust …In: Expander/powder die adjustment?
18 years ago