Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
Juan, Get yourself a reloading manual and you'll see there are a lot of choices. I use Bullse …In: Handgun Powder Selection
18 years ago
It does depend on the caliber of firearm your loading for. I personally use Bullseye for my .45acp.& …In: Handgun Powder Selection
18 years ago
I use WW231 for 9mm, .38 Special and .357 mag loads. It won't produce absolutely top velo …In: Handgun Powder Selection
18 years ago
W-231 is not likely to be discontinued anytime soon. It is fine for 9mm, too fast for 40 S&W. WS …In: Handgun Powder Selection
18 years ago
18 years ago
18 years ago
What is a good powder to use in a SDB for practice ammo? I am interested in a powder that meters wit …In: Handgun Powder Selection
18 years ago
I had a similar experience but only with very fine powder such as H110/W296. What I did was di …In: powder measure
18 years ago
I am having a problem with powder falling out of the measure after the case has dropped out of the d …In: powder measure
18 years ago
Could it be better, with round nose bullets, to use the flat adapter? Could that increase OAL consis …In: OAL varies
14 years ago
Adjust the bullet seating die with a fired case in station 1. This ensures the toolhead is loaded up …In: OAL varies
18 years ago
I was also having OAL variances, noticed some flex in my work bench. I took the time to brace it as …In: OAL varies
18 years ago
Ok, I have read everything I could find as well as your suggestion and finally took everything dow …In: OAL varies
18 years ago
If you remove the chrome e-clip from the top of the die, the die will fall out the bottom of the hou …In: OAL varies
18 years ago
Im going to load some more and recheck. Brass is the same with consistent length. Im loading truncat …In: OAL varies
18 years ago
Also, I was reading somewhere that the contact point for round nose bullets can vary up to 0.025&quo …In: OAL varies
18 years ago
FWIW, I ran a few 40S&W last night and found my OAL only varied by about 0.004" total.  …In: OAL varies
18 years ago
18 years ago
I have exactly the same problem as hookem3.Only difference is I'm using Montana Gold 180s. Is t …In: OAL varies
18 years ago
I am having a similar issue with 40 S&W with the target OAL at 1.120 Using: New unfire …In: OAL varies
18 years ago
Dillon
I did have a case in station 1 as well as every other station and all was well until I sta …In: OAL varies
18 years ago
Have a fired case in the size die when you set up the bullet seating die. this ensures the toolhead …In: OAL varies
18 years ago
DillonI have a issue with OAL on 124 9mm FMJ RN, I loaded out my first big run (500) of 9mm and foun …In: OAL varies
18 years ago
Jeffery- I have loaded 4000+ rounds on my 650 over the years. Using the case feed funnel adapter and …In: Does Anyone reload the .380 ACP on the Dillon
17 years ago
Well been trying to find reason to buy all the station one dies I can afford, and complete sets wher …In: Does Anyone reload the .380 ACP on the Dillon
18 years ago
The RCBS handgun dies lack the flared die mouth the Dillon handgun dies have. It helps to leave th …In: Does Anyone reload the .380 ACP on the Dillon
18 years ago
I was wondering if anyone reloaded the .380 on the XL 650. Seems like it is "tinkery", alt …In: Does Anyone reload the .380 ACP on the Dillon
18 years ago
hi, oojuice welcome to the reloading community, i highly recommend getting the 550 video, i to …In: Used 550
18 years ago
You will also need a good powder scale that is accurate to 0.1 grains. 7000 grains = 1 pound.& …In: Used 550
18 years ago
18 years ago
00juice since you said you are brand new to reloading I must caution you about getting loads from th …In: Used 550
18 years ago
Thanks for the info. Look forward to getting my dies, conversion kits etc and trying out this …In: Used 550
18 years ago
It appears everything is present and accounted for. The bent pin is only an attachment point where t …In: Used 550
18 years ago
/ icon and title message Hello, I just bought a used 550 on ebay that came in the mail today. I am …In: Used 550
18 years ago
I just got done loading ~3k worth of 223 in 4 hours. I have disassembled the unit to clean it. What …In: Lube for the 1050
18 years ago
I am having a problem of not being able to get 2.7 gr of bullseye powder metered out. I have reache …In: Powder Bar Assembly
16 years ago
I checked the manual and you should have the small and large powder bars included with the SDB. If …In: Powder Bar Assembly
18 years ago
If the powder charge won't go below 6 grains, then the large powder bar is installed. The small …In: Powder Bar Assembly
18 years ago
Sorry for not describing clearly. What I meant is the minimum grain I can get is about 6.0 …In: Powder Bar Assembly
18 years ago
the extra-small bar is for charges smaller than 2.5 grains. The standard small powder bar come …In: Powder Bar Assembly
18 years ago
Hi~ Read from the SDB manual, the Powder Bar Assembly has an Extra Small & Extra Large availab …In: Powder Bar Assembly
18 years ago
i have one but i dont understand what to do with it. sometimes i get a sidways primer using both l …In: Alignment pin
18 years ago
Call us and we will mail you an alignment tool at no charge. For short handgu n cases it probably is …In: Alignment pin
18 years ago
Hello, I am in the process of disassembling my 550b, and in reading some of the posts, I saw that y …In: Alignment pin
18 years ago
I have 3 Dillion 550's and 2 Dillion 1000's. I have run many thousands of CCI primer …In: CCI Primers
16 years ago