Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
The same information can be found online. But what you really need as a first purchase, is a reload …In: Complete Novice need some help!
8 years ago
And you will find out that some of the 9mm and 45 acp may have crimps too because I have been experi …In: Complete Novice need some help!
8 years ago
As far as swaging and trimming, you only need to trim if your cases are over the max case length and …In: Complete Novice need some help!
8 years ago
To answer your question about brass, .223 & 5.56 may have dimensional differences such as thickn …In: Complete Novice need some help!
8 years ago
The manual indexing of the Rl550C allows you to learn by just loading one case at a time. Then when …In: Complete Novice need some help!
8 years ago
Hey guys so I have hoarded about ~1500 Assorted .223 and 5.56 Brass also have 1K+ Factory New ammo I …In: Complete Novice need some help!
8 years ago
I load .45ACP and have put about 10K rounds through mine so far. Pausing for a second at the end of …In: Help Please...Powder sprinkle
8 years ago
Those that bleed Blue wont like hearing this, but I swapped out the Dillon powder dropper with the L …In: Help Please...Powder sprinkle
8 years ago
I had the same problem with the powder check-removed it.
I got an inspection mirror from Autozone a …In: Help Please...Powder sprinkle
8 years ago
Forgot to say I’m using WIN 231 in the 380 and Bullseye in the 9mm. I have also wrapped a anti stati …In: Help Please...Powder sprinkle
8 years ago
I have 2 XL650 set up for 380 and 9mm. Watching closely both have the sprinkle off the brass tip of …In: Help Please...Powder sprinkle
8 years ago
I doubt you can completely eliminate it. Stick powder through a small funnel tends to bridge, add so …In: Help Please...Powder sprinkle
8 years ago
I have a stock XL650 that was purchased about 4 years ago.
I mainly use this press for reloading 9m …In: Help Please...Powder sprinkle
8 years ago
You will need 357 Maximum specific dies. There is not sufficient room for adjustment due to the much …In: 357 Maximum
8 years ago
Form what I have read, you can use 38 Special/357 mag dies to resize and reload, but you will not be …In: 357 Maximum
8 years ago
ChillyB,
This part of the forum is for troubleshooting the Mr. Bulletfeeder. In the future, please …In: Jumpy Powder Meaure
8 years ago
All
Running my first batch of bottleneck rifle (223) through my 550, and was annoyed at powder fall …In: Jumpy Powder Meaure
8 years ago
No !
In theory it should, but I bought one thinking that it would and it didn't ! The 44 shell …In: 45 ACP shellplate
7 years ago
8 years ago
I know this is a dated post, but demonstrating the forum’s value, I used it today to resolve the sam …In: RL550 index sprocket can’t clear ejector wire.
6 years ago
Perfect thanks for your help, took me a minute to sort it out. I did not know it was a spring that c …In: RL550 index sprocket can’t clear ejector wire.
8 years ago
It may have been that when you were clearing the stuck case you raised the ejector wire up. It is ti …In: RL550 index sprocket can’t clear ejector wire.
8 years ago
Hi there. I have had zero issues switching between calibers for two years,but lately this has happen …In: RL550 index sprocket can’t clear ejector wire.
8 years ago
8 years ago
I use a label maker, affix the label to the front side where it can be read when on the machine. (65 …In: Engraved tool head
8 years ago
Does anyone know if Dillon plans on engraving their 550C aluminum tool heads with the caliber on the …In: Engraved tool head
8 years ago
Don't know what cartridge you're reloading but it's possible you need a bit more lube …In: Dillon Sizing/ Depriming Die.
8 years ago
First off, I’m new to reloading. I’m setting up my 550 with a Dillon Sizing/ Depriming Die. With a n …In: Dillon Sizing/ Depriming Die.
8 years ago
Invert the shellplate bolt and sprocket over a large socket. Tap on the threaded end of the bolt to …In: 550b index sprocket sticking
8 years ago
On my 550b, the index sprocket is stuck to the shell plate bolt. How do I get it off. Once off, shou …In: 550b index sprocket sticking
8 years ago
5280dillon,
You have posted this question in the wrong place. This area is for the Mr Bullet set up …In: 223 Sizing/Depriming Die
8 years ago
First off, I’m new to reloading. I’m setting up my 550 with a Dillon Sizing/ Depriming Die. With a n …In: 223 Sizing/Depriming Die
8 years ago
Remove the shellplate, and check for powder/debris around the detent ball. Normally, about half of t …In: Crushed hulls on shot station
8 years ago
I did as requested and Dillon sent me new wads guides for the 20 and 28 ga as well as new plastic sl …In: Crushed hulls on shot station
8 years ago
Please email us to request a new wad guide. Be sure to include your address, and size.In: Crushed hulls on shot station
8 years ago
It does spring back. I tried reloading some 28 gauge just last night. Three perfect shells and the …In: Crushed hulls on shot station
8 years ago
Does the spring-loaded sleeve that the plastic wad guide goes into freely spring back when pushed do …In: Crushed hulls on shot station
8 years ago
I only reload 20 and 28ga on this machine. Worked perfectly for several years then it started to cr …In: Crushed hulls on shot station
8 years ago
8 years ago
9MM is a tapered case, and has a longer carbide sizing ring and much more case contact in order to p …In: worn shell plate
8 years ago
Do these wear out or is it just me? gone though 3 in 15 years, 9mm.
But my 45acp is still good after …In: worn shell plate
8 years ago
Make sure that your loading bench is secured also. A bench that shifts and moves can have an adverse …In: Sideways primers
8 years ago
A few things to check.
Make sure the primer seating assembly is tight
Make sure the station 2 locat …In: Sideways primers
8 years ago