Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
My "plastic piece" (also known as a case feed adapter) for 9mm is green. The .380 Auto ca …In: 9mm case feeding issues
5 years ago
Sounds like you have the wrong plastic piece at the bottom of the feeder tube that is allowing more …In: 9mm case feeding issues
5 years ago
The funnel fixed the jamming at the top problem for me, however I am constantly getting 2 cases in m …In: 9mm case feeding issues
5 years ago
Is the opening at the top of the clear plastic funnel rectangular or round? Older ones were rectangu …In: 9mm case feeding issues
8 years ago
I had that same issue, and Dillon sent me AT 500 plastic funnel #16617. I haven't installed it …In: 9mm case feeding issues
8 years ago
Hello forum members. Just joined this forum. I am relatively new to reloading. I have an XL 650 i …In: 9mm case feeding issues
8 years ago
No change to the design at all. The fabric can change from lot to lot, but nothing significant. The …In: Different cover materials?
8 years ago
I purchased a cover earlier this year from a local distributor and it was more of a rounded rectangu …In: Different cover materials?
8 years ago
I just sold a the cover for my old 650, and the buyer claims that it's made out of a different …In: Different cover materials?
8 years ago
Of course, why did I not think of that.
I chose the bullet seating stem, which profile at a glance …In: bullet seating depth inconsistent
8 years ago
First, covering the obvious, be sure to use the completely flat wadcutter seat stem, and the "S …In: bullet seating depth inconsistent
8 years ago
Hi, I´m having problems with inconsistent seating depth, loading lubed lead wadcutters in .32 s& …In: bullet seating depth inconsistent
8 years ago
Push down on the edge of the shellplate between stations 2 and 3. If it feels springy, then the shel …In: Now quite lining up?
8 years ago
Make sure that you are using the correct pins for the caliber too. I reload several calibers, so I …In: Now quite lining up?
8 years ago
How would I go about getting the correct diameter specs for the pins? They seem like they touch the …In: Now quite lining up?
8 years ago
I had the same problem in station 2. I found out that my brass pins was not the right size . I measu …In: Now quite lining up?
8 years ago
Hey guys I have noticed that on certain calibers, this time I am seeing it on 380 but have seen it i …In: Now quite lining up?
8 years ago
oh my god dont no one by another manufactures press dillon is a1 on there warranties got to new l …In: no precision machining
8 years ago
Yes, the I.D. of the hole in the link arm is machined larger, to fit over the brass bearings. Pleas …In: no precision machining
8 years ago
spent 45$ on new link arm bearings (brass) #18007. clearly to big outside dia. 1.030 link arm id. is …In: no precision machining
8 years ago
The other possibility is that the ejector wire has been pried upward slightly when changing shellpla …In: Another high primer thread
8 years ago
Hello, I have a new 550C and am loading 45 Auto small primer brass (Blazer Brass of this caliber has …In: Another high primer thread
8 years ago
in general, we estimate a load of media will clean about 20-25 full loads of brass. Eventually the i …In: Corn cob and other media
8 years ago
When it stops working or takes much longer than normal to get the results you want.
Actual times wi …In: Corn cob and other media
8 years ago
8 years ago
I have pulled the press apart and cleaned/lubed everything. The indexing pawl is jumping when the i …In: Pawl jumping on downstroke
8 years ago
It is unnecessary to use a case gauge with 45 Auto Rim. This round is a straight wall case used exc …In: Case gauges
6 years ago
6 years ago
8 years ago
If you have multiple firearms that you're shooting the same caliber or semi autos, the case gau …In: Case gauges
8 years ago
How important/critical is the use of a case gauge? And is a case gauge more important with rifle o …In: Case gauges
8 years ago
8 years ago
If I had to do this, I would put the item in a vise and slowly close it while using a caliper to tes …In: Primer seating cup to high
8 years ago
Looking for options to re-seat the primer seating cup to the proper height 1.215" to 1.220" …In: Primer seating cup to high
8 years ago
I had the same problem exclusively with Winchester primers two years ago, several different lots. W …In: primers jamming in pick up tube
7 years ago
We regularly measure the height and concentricity of primers. The current production of several bra …In: primers jamming in pick up tube
7 years ago
Just a suggestion: make sure that the plastic tip is fully seated on the pick-up tube, having a slig …In: primers jamming in pick up tube
7 years ago
I have been having problems with this also. I have been using Winchester Large Pistol Primers " …In: primers jamming in pick up tube
7 years ago
I hope you have found a solution by now. If not, I found that some of the primers are slightly over …In: primers jamming in pick up tube
7 years ago
Ed,
What size primer tubes are you using? There are two sizes, and if you are picking up small pri …In: primers jamming in pick up tube
8 years ago
Hi My outfit is relatively new xl650 . A continuing problem is the primer pick up tubes . After 10 …In: primers jamming in pick up tube
8 years ago
When sold by Dillon, the SDB includes a separate primer slide assembly and magazine tube for the siz …In: Parts needed for small to large primer caliber conversion
8 years ago
Hi,
Buying a SDB as soon I figure out the answer the the question here. Buying SDB with .38 setup. …In: Parts needed for small to large primer caliber conversion
8 years ago
I took out my dad's old 1200 gr scale and was going to load up some 223, but when I put the 700 …In: 1200 gr D-Terminator
8 years ago
The spent primers are getting jammed onto the end of the depriming pin. There are two different appr …In: Deprime issue
8 years ago
Every 10 to 30th round I have a spent primer get reseated in the case it was removed from. This prob …In: Deprime issue
8 years ago