Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
According to the users manual, in the Cross Reference Chart - page 19:
Shellplate B, Locator Button …In: .308 norma mag
8 years ago
I HAVE A DILLON550C I CANNOT FIND A SHELLPLATE FOR A .308 NORMA MAG. MY .308 WIN WONT WORK BUT MY 7M …In: .308 norma mag
8 years ago
The new loaded round ejector chute arrived in today's mail.
Thank you!In: Cam Slide Catching Ejector Chute
8 years ago
Thank you. Request sent on the contact form and address included.
JoeIn: Cam Slide Catching Ejector Chute
8 years ago
It sounds like the loaded cartridge chute/bracket is bent. In the short term, use a zip tie to secur …In: Cam Slide Catching Ejector Chute
8 years ago
I'm not sure why this is happening and it only seems to happen when I've changed to .30-06 …In: Cam Slide Catching Ejector Chute
8 years ago
So I have started reloading for 7.62x39, I have doing 223, 308, 45, and 9 for a while now other than …In: 7.62x39 and cmmg mk47
8 years ago
So I have started reloading for 7.62x39, I have doing 223, 308, 45, and 9 for a while now other than …In: 7.62x39 and cmmg mk47
8 years ago
So I have started reloading for 7.62x39, I have doing 223, 308, 45, and 9 for a while now other than …In: 7.62x39 and cmmg mk47
8 years ago
You may only have needed to run a swab with alcohol thru them to make sure no debris is in them. You …In: pick up tube problem
8 years ago
What brand primers are you using? I've loaded around 13k or so and haven't had issues wit …In: pick up tube problem
8 years ago
I have had a 550 C for a month. Works fine. I have loaded 1000 9mm so far. At first my small caliber …In: pick up tube problem
8 years ago
I go through and deprime all the cases and clean cases again to clean out the primer cup. While the …In: Occasional missed primer
8 years ago
OK, went thru the cleaning & lube procedures. I was amazed at the amount of gunk in the primer f …In: Occasional missed primer
8 years ago
8 years ago
Thanks for the info. I wondered about the white plastic plunger. I will check it carefully. No reas …In: Occasional missed primer
8 years ago
2x on the debris along the ramp, but also there could be an issue with the white plunger sticking. …In: Occasional missed primer
8 years ago
Thanks for the quick response. I'll do a through clean. Hope that clears the problem.In: Occasional missed primer
8 years ago
Check for debris inside the primer slide housing that might prevent the slide from going all the way …In: Occasional missed primer
8 years ago
A problem just started to occur. Out of, say, 100 primers, might miss 4 or 5. Pull the handle again …In: Occasional missed primer
8 years ago
I see you put in the large primer punch... did you change to the large primer system and use the cor …In: indexing issues after switching from the small primer disc to the large primer disc
8 years ago
If you raise the platform slightly, how does the action feel when you try to manually forward the pr …In: indexing issues after switching from the small primer disc to the large primer disc
8 years ago
Since it is fairly new, I will assume it is not a lube issue. Dillon has a good video on lubing on …In: indexing issues after switching from the small primer disc to the large primer disc
8 years ago
So I have been reloading for a couple of months on my new XL 650 and on the small primers for both . …In: indexing issues after switching from the small primer disc to the large primer disc
8 years ago
Get an RCBS Stuck Case Remover and you will be able to pull the stuck case. Also start using Imperi …In: 308 Help
7 years ago
Well I have tried reloading the 308 again and this time the brass is stuck in the size die and is st …In: 308 Help
7 years ago
The 308 Winchester case does require considerable effort to resize, do to the case geometry. When ad …In: 308 Help
8 years ago
I have reloaded many thousands of rounds of 9mm, 40 S&W, and 45 ACP in the past on my 550B press …In: 308 Help
8 years ago
That's a manual for the v2... unfortunately I must have gotten old stock last month and receive …In: Casefeed manual
8 years ago
Thank you. I overlooked it because it wasn't where the 550 casefeed was and didn't have & …In: Casefeed manual
8 years ago
I was wondering if there was a pdf of the 650 casefeed manual? If so why was it not listed in the M …In: Casefeed manual
8 years ago
I'll tell you what I do for what it's worth. I have run thousands of rounds the same way a …In: 5.56 workflow and clarification
8 years ago
Tonewheelz,
The second video is the correct one.
When I load 556 or 300 blackout, I use a short …In: 5.56 workflow and clarification
8 years ago
I’ve been looking at some videos of the Dillon 650 with the purpose of loading 5.56/223, trying to l …In: 5.56 workflow and clarification
8 years ago
All Dillon pistol sets are carbide. Dillon rifle sets are usually available in either carbide or ste …In: Carbide Die sets
8 years ago
How interesting, all of my pistol sets are listed as "Standard" but the resize dies are al …In: Carbide Die sets
8 years ago
8 years ago
Are all of the dies in a carbide die set carbide? Or just the resize die? The reason is that I hav …In: Carbide Die sets
8 years ago
6.5 Creedmoor uses:
6.5 shellplate
6.5 Grendel powder funnel
#1 station One Locator
3-#1 brass locat …In: 375 Ruger, 28 Nosler, 6.5 creedmoor
8 years ago
Thank you for such a quick response.
That is way fewer parts than I was expecting. Can you give me …In: 375 Ruger, 28 Nosler, 6.5 creedmoor
8 years ago
We have conversion kits for 6.5 Creedmoor ( #62245) and 28 Nosler ( #62298). We haven't worked …In: 375 Ruger, 28 Nosler, 6.5 creedmoor
8 years ago
I’ve got an xl650 with auto case feeder and the required parts and conversion kits to load for 9mm, …In: 375 Ruger, 28 Nosler, 6.5 creedmoor
8 years ago
The 338 lapua shell plate does not fit my 300 norma (lapua, norma, peterson) brass. The brass won& …In: 300 Norma shell plate ???
6 years ago