Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
6 years ago
I decided to give Scheels a try. I ordered a bullet tray and a powder measure last night at 11 PM a …In: Scheels
5 years ago
5 years ago
I ordered my XL-750 from Scheels a few weeks ago when no one else had any and it shipped out the sam …In: Scheels
6 years ago
I saw that Scheels had a lot of things "in-stock" that were not in stock anywhere else, an …In: Scheels
6 years ago
Scheels has XL-750s listed in stock again in .223. You could always add a caliber conversion kit in …In: Scheels
6 years ago
Dillon was kind enough to send a standard case feeding tube with the smaller ID to replace the large …In: 223/5.56 CaseFeed Tube Jams
5 years ago
BTW, got an email from Dillon saying the ID of the case feeder drop tube is supposed to be about 0.5 …In: 223/5.56 CaseFeed Tube Jams
6 years ago
Didn't get out to look for smaller ID tubing, so took a length of clear packing tape, folding i …In: 223/5.56 CaseFeed Tube Jams
6 years ago
I have had that happen several times with .223 cases, also. I measured the tube inside and outside …In: 223/5.56 CaseFeed Tube Jams
6 years ago
Ok, I finally got the 650 set up for a run of 223, and after three cartridges, the empty cases are j …In: 223/5.56 CaseFeed Tube Jams
6 years ago
Among all the calibers used for the AR-15, the 6.5 Grendel is the best in business. The weapon is kn …In: Best AR-15 Caliber
6 years ago
There are several factors why you should try the AR-15 for home defense. Firstly, you need to unders …In: AR-15 For Home Defense
6 years ago
The upgrade from the 550B to the 550C seems pretty straight forward. You can buy a kit to upgrade, i …In: Dillon 550 versions: What changed.
6 years ago
Hi,
I am having primer seating issue using large CCI-200 primers loading a 308Win. I am using Lapua …In: Primer seating issue
6 years ago
I think the blue tips are on the newer style and I read somewhere that there were clear plastic tube …In: Primer Tube Blue Tip???
6 years ago
Just discovered the brass tipped primer tube mentioned directly above is the "large primer" …In: Primer Tube Blue Tip???
6 years ago
BTW, I just found another mystery primer tube. This on has a brass tip with no hole/primer keeper pi …In: Primer Tube Blue Tip???
6 years ago
I’m in the process of dusting off my 650, and found some primer tubes, one large, one small, with a …In: Primer Tube Blue Tip???
6 years ago
I own a SDB and have loaded about 20,000 rounds without an issue. All the sudden my Bullets are spin …In: Bullet spins
6 years ago
Just call them. They have outstanding customer service. Does it need to be rebuilt? Maybe just taken …In: Rebuild a 550B?
6 years ago
Hello,
I've heard that Dillon will rebuild a 550B press if I send it in. Can someone educate m …In: Rebuild a 550B?
6 years ago
The 6.5 rim is .468 vs. .469 for the.308 and the extractor groove for the 6.5 is .397 and .404 for t …In: 6.5 Creedmoor Shell plate
6 years ago
Hello
Is the 308/30-06 shellplate compatible with the 6.5 creedmoor case for the 550b?In: 6.5 Creedmoor Shell plate
6 years ago
Yesterday I replaced the Magazin tube. The tip of the old tube was damaged.
After that, I checked t …In: Refit XL650 to XL750
6 years ago
PS. excuse my Grammar as I am german. I am trying to write as good as I can with the technical Terms …In: Refit XL650 to XL750
6 years ago
Thanks for your help,
to answer almost every Question there: yes.
But: I will check the set screw …In: Refit XL650 to XL750
6 years ago
Here's what you need to know, you know?
–You know that there are parts for small primers and l …In: Refit XL650 to XL750
6 years ago
There are issues with the Priming System.
After Setting up and checking without primers, everything …In: Refit XL650 to XL750
6 years ago
There seems to be a different platform used on the '750 so there is likely no easy conversion. …In: Refit XL650 to XL750
6 years ago
I have a XL 650 with primer seating issues and want to upgrade to the Priming System of the 750.
Is …In: Refit XL650 to XL750
6 years ago
Yes. I set it so that there is no tension on the shell casing when it is in place. The problem is …In: cartridge spring adjustment
6 years ago
It is not necessary to trim the cartridge spring. By loosening the cartridge spring retaining screw …In: cartridge spring adjustment
6 years ago
When I insert a 45acp cartridge (and others) into station 1, the cartridge spring does not fully mov …In: cartridge spring adjustment
6 years ago
> I ended-up taking .080" off the drop tube of the powder dispenser when I had it off to pol …In: Trouble with .40 S&W
5 years ago
> I ended-up taking .080" off the drop tube of the powder dispenser when I had it off to pol …In: Trouble with .40 S&W
5 years ago
> problem completely solved and I'm done messing with it
I ended-up taking .080" off t …In: Trouble with .40 S&W
5 years ago
I cut off the bottom of the funnel. I still have about 1/8" of powder bar travel somehow, but …In: Trouble with .40 S&W
6 years ago
I just started loading .40 S&W. When adjusted for full powder bar movement and slight belling o …In: Trouble with .40 S&W
6 years ago
With the SDB press, do the 9mm 115 gr. Hornady XTP and HAP bullets use the same RN FMJ type seating …In: Which Seating Die
6 years ago
Can you acceptably trim 7mm-08 with a 308 win. size/trim die in the rt1200/1500?
A 243 is has a 6 mm …In: 7mm-08 trim die
6 years ago
You will need a scale that measures in grains to dial in powder charges (mechanical or electronic po …In: Future newbie
6 years ago
Looking to get reloading. Besides base SDB what accessories do I “really” need. Just shooting pistol …In: Future newbie
6 years ago
The conversion kit I have lists .308, .30-06, and .30 TC on the box and my black casefeed adapter al …In: Casefeed Adapter XL 750 for 308
6 years ago
I found my answer in aroundabout way...
I found a 3D printer file for a 308 casefeed adapter, and op …In: Casefeed Adapter XL 750 for 308
6 years ago
I've got two black Casefeed adapters that came in different used XL650/750 conversion kits that …In: Casefeed Adapter XL 750 for 308
6 years ago