Please to create posts and topics.

Post History: Reloader

Reloader

User

The bowed washers are thin enough to fit. No compelling reason to remove them.In: RL 550B to RL 550C Upgrade

7 years ago

I just upgraded my RL 550B to RL 550C with the Dillon upgrade kit. I have an older RL 550B and it us …In: RL 550B to RL 550C Upgrade

7 years ago

It sounds like the white delrin bushing that goes into the connector body collar might be missing.De …In: SDB Rattles

7 years ago

My SDB sounds like a rattle trap. The whole powder tube, and powder measure up are really loose and …In: SDB Rattles

7 years ago

The case feeder was redesigned the beginning of 2018 to allow the metal cuff to be adjustable. It ha …In: 300 blackout case feeder plate

7 years ago

How would one know if their case feeder mouth was adjustable...just looking at it I would say no, bu …In: 300 blackout case feeder plate

7 years ago

If your case feeder has a fixed opening size in the bowl where cases fall out, use a pistol case fee …In: 300 blackout case feeder plate

7 years ago

I use the large pistol plate with two spacer washers underneath the clutch. This required getting lo …In: 300 blackout case feeder plate

7 years ago

Hey what size case feeder plate would I use in my case feeder for 300 blackout?In: 300 blackout case feeder plate

7 years ago

Broken parts like this are covered under warranty. Please phone or email us for warranty replacement …In: 550c huge disappontment

7 years ago

Thanks for your help. My problem is that the plastic washer or bolt does not fit into the return br …In: 550c huge disappontment

7 years ago

You should probably phone us when you can be in front of the machine. The case-activated powder meas …In: 550c huge disappontment

7 years ago

Recently bought a 550C.. I've had nothing but problems since day one. The main issue is the fai …In: 550c huge disappontment

7 years ago

Thank you for the reply. If it ever stops raining in Indiana, so I can go back to work ( I cut grass …In: REBUILD?

7 years ago

Yes, we do. We charge a $79.95 clean and lube fee, plus the cost of any parts if you want any possib …In: REBUILD?

7 years ago

I just bought my third Dillon press. It is a older model 550. My question is does Dillon still rebui …In: REBUILD?

7 years ago

Check the powder funnel and compare it to the manual, to ensure the correct powder funnel is being u …In: Powder die/measure setup issue

7 years ago

same thing here... still isn't workingIn: Powder die/measure setup issue

7 years ago

You probably need to snug the nylock nut on the bellcrank bolt another 1/2 turn or so. This will pre …In: Powder die/measure setup issue

7 years ago

Setting up my new 550C for 9mm. Followed instructions on setting up the powder die/funnel/measure. …In: Powder die/measure setup issue

7 years ago

Your scale was probably made in 1993. Please email us for a return authorization. Include your name …In: Terminator Scale

7 years ago

The scale S/N is 24660232139, tag still on bottom of scale. I believe it was purchased in the later …In: Terminator Scale

7 years ago

I have an older terminator scale that was purchased years back. I bought the 550 press and several t …In: Terminator Scale

7 years ago

At the rate things are going.....my Terminator scale will be out of warranty by the time the freakin …In: Terminator scale

7 years ago

Your scale was probably made in 1993. Please email us for a return authorization. Include your name …In: Terminator scale

7 years ago

The scale S/N is 24660232139, tag still on bottom of scale. I believe it was purchased in the later …In: Terminator scale

7 years ago

All electrical and electronic equipment produced after July 1, 1999 has a one year warranty. When di …In: Terminator scale

7 years ago

I have an older terminator scale that was purchased years back. I bought the 550 press and several t …In: Terminator scale

7 years ago

Thank you Dillon Administrator. I'm guessing the difference between the two measurements is du …In: Is my bench too tall to use the Strong Mount + case feeder ???

7 years ago

I don't use a strong mount simply because I do not stand when reloading and that is what it is …In: Is my bench too tall to use the Strong Mount + case feeder ???

7 years ago

Cool. That sounds like I'll have enough room to scoop in the brass with good clearance from …In: Is my bench too tall to use the Strong Mount + case feeder ???

7 years ago

36" tall bench is typical. Add 44 1/2" to 46 1/2" for the 650 on a strong mount with …In: Is my bench too tall to use the Strong Mount + case feeder ???

7 years ago

Hello foks. I'm in the beginning stages of getting all my gear for the bench and then was orde …In: Is my bench too tall to use the Strong Mount + case feeder ???

7 years ago

I've reduced my flare to .01 it was at .02. I've made sure my crimp is to load data spec. …In: Newbie Questions

7 years ago

Canadianshooter, We recommend flaring the case mouth between .010" -.020" larger than the …In: Newbie Questions

7 years ago

It's a shoulder bolt. Just make sure it's snug, but don't stand on it. What bullet a …In: Newbie Questions

7 years ago

1. How tight do you tighten the shell plate retaining bolt? I've read they can snap off. I don& …In: Newbie Questions

7 years ago

If the rod is not vertical, it means the powder die is towards Station 1 or 3. If it's centere …In: FailSafe Rod 550C

5 years ago

Had the same issue yesterday called tech Support had to send a picture still no response Fixed it …In: FailSafe Rod 550C

5 years ago

Did you end up replacing the plastic bushing? . Mine just broke in half. Trying to figure out if I n …In: FailSafe Rod 550C

5 years ago

Same problem. Mine broke the white plastic bushing. I wrapped the rod in tape so not to scratche it …In: FailSafe Rod 550C

6 years ago

I have the same issue!! Tech support was no help, videos were no help eitherIn: FailSafe Rod 550C

7 years ago

Check the lower bend on the failsafe rod. The rod should hang vertical, =/- 5 degrees or so. If nece …In: FailSafe Rod 550C

7 years ago

Hi, I'm trying to setup my new 550C with .223 Caliber conversion kit but my Failsafe Rod canno …In: FailSafe Rod 550C

7 years ago

Thank you. I dont feel comfortable messing with the plug adjustment so I just bought some hornady ma …In: I'm either loading sub moa ammo/or unshootable 223 ammo

7 years ago

Hornady uses a slightly different radius than other brands of bullets, but this should not affect co …In: I'm either loading sub moa ammo/or unshootable 223 ammo

7 years ago

As the title states. It's one or the other and incredibly frustrating (for 223 rem). I have a …In: I'm either loading sub moa ammo/or unshootable 223 ammo

7 years ago

Cool. I'm using the Skylight kits from Inline Fabrication. Love 'em.In: Light

7 years ago

Great idea, I use a stick on 4 LED light that came with a leather sewing machine. Very handy since …In: Light

7 years ago

I have seen where you can buy a light to mount to your press, to see what's going on better. I …In: Light

7 years ago