Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
I am wanting to set up a 650 just for brass...I don’t need anything but the bare minimum. Don’t need …In: .223 brass processing
7 years ago
I know it voids the warranty...it could possibly crack the frame. That’s why I was looking for a use …In: .223 brass processing
7 years ago
First, be aware that installing a swager on the XL650 voids the warranty. Dillon Precision does not …In: .223 brass processing
7 years ago
I am wanting to set up a 650 just for brass...I don’t need anything but the bare minimum. Don’t need …In: .223 brass processing
7 years ago
Use a pair of pliers or put the primer cup and and platform in a vice, loosen the set screw on the s …In: 450 problems
7 years ago
Often times the alignment of the primer feed system is out of wack and needs to be adjusted. Also, t …In: 450 problems
7 years ago
There should be a set screw on the side of the primer arm that holds the primer seating punch in pla …In: 450 problems
7 years ago
no primer in the cup, the primer seater seems to be sticking up past the shell holder. the ram does …In: 450 problems
7 years ago
Are you attempting to slide a case into station 1 with a primer in the cup? If so, the primer will u …In: 450 problems
7 years ago
bought a used 450 and after clean up and lubing the shell plate does not stay above the primer cup a …In: 450 problems
7 years ago
When processing brass, most people use a universal depriming die in station 1, and set up the trimme …In: 223 case trimming
7 years ago
I want to start reloading 223 in my xl650. I’m wondering how you handle trimming the casings th …In: 223 case trimming
7 years ago
Carbide rings are secured in three different ways. The carbide is a slight press fit into the die bo …In: Size/Deprime tool - carbide sizing ring loose
7 years ago
I'm a happy owner of a Dillon XL650 that has worked pretty much as expected through the last 4 …In: Size/Deprime tool - carbide sizing ring loose
7 years ago
Yes, this is common. Usually the anvils sit higher than handgun primers for safer transport. No worr …In: Shell plate not clearing primer
7 years ago
You are correct. Sorry. I was trimming for 4 to 5 hours before I wrote this, so I was a little burnt …In: Shell plate not clearing primer
7 years ago
When you are actually loading progressively on the machine, there is never a primer in the primer cu …In: Shell plate not clearing primer
7 years ago
Hello again,
I recently switched from 9mm to 223 on my 550c. I started with 9mm and 223 is the seco …In: Shell plate not clearing primer
7 years ago
Only the unmachined casting is the same. After the frame is machined to accept the SL900 toolhead, i …In: SL 900 conversion to rifle reloading?
7 years ago
I recently acquired a SL 900 from a friend, and noticed that the frame is stamped with "650&q …In: SL 900 conversion to rifle reloading?
7 years ago
Thank you. I turned it another 1/8 turn and that is all it needed.In: I am not sure if I'm having sizing issues or not (223/556 on 550c)
7 years ago
When you thread the size die down past touching the top of the shellplate, you are taking any play o …In: I am not sure if I'm having sizing issues or not (223/556 on 550c)
7 years ago
I have a 550c. I dont have anyone to teach me how to load, so everything ive learned is from dillon …In: I am not sure if I'm having sizing issues or not (223/556 on 550c)
7 years ago
I know this is an old thread, but I thought I would share my thoughts.
I just received mine yesterd …In: success with RF 100
7 years ago
Walter,
In my experience, these machines are very fussy. Took me a while to figure out my machine o …In: success with RF 100
7 years ago
I was having similar problems with LP primers when I went to Winchester primers. Federals were grea …In: success with RF 100
7 years ago
7 years ago
I don't know where all you have looked. Hodgdon is the company which does titegroup. They have …In: Reloading 9mm HP
7 years ago
I have the round nose 125 gun down as far as COL and powder it really consistent. I got a box of JH …In: Reloading 9mm HP
7 years ago
Yes there is an upgrade kit. Give Dillon a call and they will sale you one.In: Failsafe powder assembly for older powder measure
7 years ago
Is it possible to get the upgraded failsafe assembly for the old style powder measure?In: Failsafe powder assembly for older powder measure
7 years ago
7 years ago
Our sincere apologies. This is indeed a typo. We aren't sure how it occurred, but it is being a …In: casefeed plate
7 years ago
Casefeed instruction manual dated Jan. 2018 (ver. 2) page 8 specifies small rifle casefeed plate fo …In: casefeed plate
7 years ago
Mine didn't fit the Super 1050 for that matter - apparently just a tolerance/QC at whoever is m …In: Part #20341
7 years ago
There is no dimensional difference in the slot width, other than tolerances. Measure the screwdriver …In: Part #20341
7 years ago
I ordered the screwdriver, 20341 to investigate why my primer punch wasn’t sitting flush, and have f …In: Part #20341
7 years ago
The Super Swage 600 is the fastest separate swaging tool we are aware of. It bolts to your bench, an …In: Swaging
7 years ago
Thank you. I will steer clear.
What is the recommended method for high volume swaging? Without purch …In: Swaging
7 years ago
What's the best way to save high volume? I just purchased a 650 and don't even have it set …In: Swaging
7 years ago
Did you readjust the station 2 locator? It needs to be within .002-.004" of touching the side o …In: Cases are destroyed in the powder die
7 years ago
Did you readjust the spring-loaded station 2 locator? This needs to be set to within .002-.004" …In: Cases are destroyed in the powder die
7 years ago
Hello, I’ve been having problems whit the powder die. When the case goes up it isn’t centred whit th …In: Cases are destroyed in the powder die
7 years ago
Can you post a photo? What caliber?
If the case mouth is rolling inward, the most likely cause is th …In: dented cases
7 years ago
On the upstroke in station 2 the powder station, 1 out of 12 cases gets dented at the top of the cas …In: dented cases
7 years ago
Push down on the edge of your shellplate between stations 2 and 3. If it feels springy, then the she …In: 550 PM slipping
7 years ago