Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
While posting to the XL-750 board, I believe this info applies to all Dillon presses with interchang …In: Reducing COL variations
6 years ago
The XL750-only strong mount adds 6 3/4" to the height. The RL550/XL750 mount is taller, adds 8 …In: XL750 cube dimension
6 years ago
Hi there. I am interested in purchasing this model reloader. You mention the press with case feede …In: XL750 cube dimension
6 years ago
George
My setup is about 19-20 inches deep. It will depend on how you mount the press in relation t …In: XL750 cube dimension
6 years ago
I’m a first time Dillon owner. My new xl750 is going to be delivered soon and I need some advice abo …In: XL750 cube dimension
6 years ago
I don't know any tricks other than removing the primer tube housing and dumping them out the to …In: Removing Leftover Primers
6 years ago
What is the easiest way to remove excess primers from the Dillon 550b primer feed tube? I reloaded …In: Removing Leftover Primers
6 years ago
Several items can cause this:
Are all the cases out of the machine? If not one could be part sl …In: Shell Plate Issue
6 years ago
My shell plate does not rotate when I activate the handle (pull and release). I'm sure its som …In: Shell Plate Issue
6 years ago
You see where the mayors of Champaign, IL and New Orleans, LA have taken it upon themselves to ban t …In: Mayors Exceeding Their Authority
6 years ago
Found part of the problem, adjusted the primer cup height. It was too high by .07", brought it …In: Large Primer Magazine Orifice
6 years ago
It seems every time I change from small primers to large primers, I have to get a new orifice becaus …In: Large Primer Magazine Orifice
6 years ago
If you move the metal piece @ the area where the brass falls into the tube.....approximately 3/4 inc …In: 300 Blackout feeding problems
6 years ago
If you have a large pistol case feed plate, use it, along with the two washers. It will pick up case …In: 300 Blackout feeding problems
6 years ago
I have an older collator. Directions say to use the small pistol plate with the two washers install …In: 300 Blackout feeding problems
6 years ago
6 years ago
The crank pin is hardened, so all you need to do is use a wire wheel or cratex wheel to clean off an …In: Galled Crank Pin and Shell Plate indexing
6 years ago
Hello,
At one point about 5 years ago I remember having a problem with a hard pull on the Crank Han …In: Galled Crank Pin and Shell Plate indexing
6 years ago
Remove the cartridge from the shellplate after you seat the bullet, but before you crimp. Can you ro …In: .380 crimp problem
6 years ago
Some things to check for:
Make sure you are using the correct diameter bullet .355-.356
You should b …In: .380 crimp problem
6 years ago
Hi guys. I'm reloading .380 on my new 550C press and I can't found a correct crimp. The cr …In: .380 crimp problem
6 years ago
I have the same problem, except my XL-650 is approx 8 years old. I used it for awhile 8 yrs ago and …In: Casefeed Problem
6 years ago
I would try the slightest bit of light lubricating oil at the top and bottom where the bolt goes thr …In: Casefeed Problem
6 years ago
I have a new 650 and every few pulls the small arm with the bushing that moves under the drop tube f …In: Casefeed Problem
6 years ago
Why did you guys make us build new user accounts? I've had my account for many years and it wor …In: Why Dillon ????
6 years ago
I had similar problem that reloaded rounds don't gauge. Now I trash the Aguila brass.In: Aguila brass
6 years ago
It could be crimped. Look for a ring around the primer pocket. If this is the case, swaging the prim …In: Aguila brass
6 years ago
I having issues attempting to reload once fired Aguila 9mm brass, on two of my 550 b machines. using …In: Aguila brass
6 years ago
remove the die lock ring, and adjust the die. As long as at least one full thread is visible above t …In: Station 4 - Seating Die
6 years ago
You should be able to put a lock ring on the under side of the toolhead. If the brand of die you ar …In: Station 4 - Seating Die
6 years ago
Hi
New XL750. Setting up for 9mm. Using Campro semi wad cutter bullets. I have run out of adjustmen …In: Station 4 - Seating Die
6 years ago
6 years ago
Hey guys,
I would like to be able to load in either 9mm or 38 Super in my SDB.
What are the additi …In: 9mm <—> 38Super
6 years ago
Check the connector body collar, the bottom portion of the powder measure that attaches to the top o …In: powder
6 years ago
having problems with my square deals.Have 3 set ups.2 of them ,the powder charge portions varies plu …In: powder
6 years ago
6 years ago
Nevermind, I wasn't seeing it right. Not sure if it's the correct way but I just rotated …In: Removing Primer Punch?
6 years ago
Is there a trick to this? Trying to convert from 9mm to 45 ACP. Changeover was a breeze until this …In: Removing Primer Punch?
6 years ago
IT is extremely unlikely that it is. MOre likely, there is a tiny bump in the center of the primer s …In: Denting primer
6 years ago
6 years ago
You need the white "380" adapter. Also, be sure you are using the #3 shell plate and the …In: 380 problems
6 years ago
Reading all old posts I’ve ordered the white adapter. Hopefully that fixes the one problem. Now a li …In: 380 problems
6 years ago
I have a xl650 that’s just over a year old. When loading 380’s the case feeder is locking up. I hav …In: 380 problems
6 years ago
I just broke in my new XL750 by running 2,800 9mm 124gr jhp rounds. Early on I noticed thumb pressu …In: Bullet setback
6 years ago
Yeah that is the problem is I ordered mine from Graf and Sons online. They appear to be a bigger sto …In: Just ordered 750. How do I know if it is old stock with priming issue?
6 years ago
The tec. I talked with a Dillon said the issues were corrected late Sept. 2019. I ordered my machin …In: Just ordered 750. How do I know if it is old stock with priming issue?
6 years ago
Just ordered my 750 from Graf and Sons. I am curious as to how I will know if it is old stock with t …In: Just ordered 750. How do I know if it is old stock with priming issue?
6 years ago