Please to create posts and topics.

Post History: Reloader

Reloader

User

Can an RL450 accept the roller handle and strong mount for a 550? ThanksIn: RL450 Upgrades

17 years ago

I'm a little late on this thread, but hope fully others will benefit. I removed the ti …In: Watch out for flying primers!

15 years ago

I get this question quite a bit." How come primers always pop out all over my work bench and fl …In: Watch out for flying primers!

16 years ago

My XL650 has the alloy platform. The only time I notice any quantity of spent primers on the shop fl …In: Watch out for flying primers!

16 years ago

MINE IS THE NEWER ALLOY. In: Watch out for flying primers!

17 years ago

How old is your machine? Is the platform made of steel or alloy? When the platform was redesigned …In: Watch out for flying primers!

17 years ago

I have the same problem. I do have the cup in the correct way. I have tried foam, cardboard, little …In: Watch out for flying primers!

17 years ago

Try turning the cup around. The little extenson tip should be facing the machine.In: Watch out for flying primers!

17 years ago

I have a small problem with capturing spent primers in the small bin underneath station 1 of my 650x …In: Watch out for flying primers!

17 years ago

Official policy , right from the instruction manual, is the addition of any unapproved equipment fro …In: upgrades 1050

17 years ago

hi does dillon endorse the use of electric drive systems on the 1050? "its looks like dillo …In: upgrades 1050

17 years ago

I would say that an hour is a good middle of the road time frame for changing out calibers and getti …In: calibur swap

16 years ago

Don't worry about the trimmer motor getting hot. It is a sealed DC motor, and oerates on …In: calibur swap

17 years ago

To swap out tool heads and calibers, figure an hour to make sure you clean, lube and verify all the …In: calibur swap

17 years ago

hi all from the uk seriously interested in the 1050 but not a popular brand here in the uk,so not …In: calibur swap

17 years ago

I've decided to just use magnum primers for all my pistols these days... I just received 20K of …In: Primers

17 years ago

Magnum primers are necessary for some, but not all powders. W-296, H-110, AA-9 all require a magnum …In: Primers

17 years ago

I know someone has asked this question before, and I looked through the forum but I didn't see …In: Primers

17 years ago

I have also found that if the locater is cleaned really good, a couple of coats of 3m Dry Silcone wo …In: station-one locator

17 years ago

the underside of the station one locator should have a coating of grease to act as a vibration …In: station-one locator

17 years ago

I just setup my new 650 and have loaded about 500 rnds of 223. (It came factory setup for 223) …In: station-one locator

17 years ago

Sweet!!! Thanks for the input!In: Hornady Dies in my 650 - Crimp question

17 years ago

No problem at all. Adjust the dies exactly as you described, and it will work fine.In: Hornady Dies in my 650 - Crimp question

17 years ago

Greetings fellas. Gotta question for those of you are experinced reloaders. I have a Dil …In: Hornady Dies in my 650 - Crimp question

17 years ago

ermd3, Do you currently own an RL450? If not, it is not cost-effctive to piece one together. …In: RL 450B

17 years ago

Can i just buy the RL450B frame change kit as my "base" and slowly buy the other kits (pow …In: RL 450B

17 years ago

The frame change kit gives you the interchangable toolhead capability, and it uses the same conversi …In: RL 450B

17 years ago

Are the conversion kits for the RL450B the same as the ones for the 550B?In: RL 450B

17 years ago

So, after the conversion, it will have the removable tool heads and everything? I am consideri …In: RL 450B

17 years ago

TL is a typo. Is only the RL550B. There no single kit to convert an RL450B into an RL550B. Frame …In: RL 450B

17 years ago

I understand that it is possible to convert the RL 450B to a 550B... To be precise, Dillon's we …In: RL 450B

17 years ago

Never SUPPOSED to happen - but primers are little explosives and "stuff" does happen occas …In: Rumor or Truth

17 years ago

A single primer explosion is possible if you try to seat a reluctant primer too agressively. …In: Rumor or Truth

17 years ago

GeoK, I've had my 650 for about 4 yrs. now & have loaded about 9-10,000 rds. of 223, 9mm, 4 …In: Rumor or Truth

17 years ago

Primer explosions can and do happen in every brand of reloader that holds multiple primers. The init …In: Rumor or Truth

17 years ago

I've owned my 650 for a couple of years now, reloaded about 15000 rounds, and have not had a si …In: Rumor or Truth

17 years ago

I've owned my 650 for a couple of years now, reloaded about 15000 rounds, and have not had a si …In: Rumor or Truth

17 years ago

I have reloaded 1000's of rounds on my XL650. Only one time I had a primer that had gotten stuc …In: Rumor or Truth

17 years ago

I am interested in purchasing a XL650 but have heard that there are cases of the entire primer tube …In: Rumor or Truth

17 years ago

Good afternoon Gents, I had the same trouble with Unique dribbeling 3 to 5 flakes out the top of t …In: Extrudede Powder Blues

15 years ago

hugo, i run a 200g jfp from Montana gold bullet in my 45acp. i use 5 grains of Winchester super tar …In: Extrudede Powder Blues

16 years ago

WW231 also meters very well and I believe it's a ball powder.In: Extrudede Powder Blues

17 years ago

Sounds good to me. I'll save the Unique for reloading shotgun, and continue to use the 700x aft …In: Extrudede Powder Blues

17 years ago

these are not extruded powders, but actually flake powders. Unique is a very bulky powder, wit …In: Extrudede Powder Blues

17 years ago

I reload on the XL650. I was reloading 45acp with Unique and 700x. Both are extruded and both are a …In: Extrudede Powder Blues

17 years ago

I made a spent primer chute from a 308 case. Cut it off, petaled the end, bolted it on, and stuck a …In: spent primers

11 years ago

Almost. The top of the chute appears a little short at the top.In: spent primers

17 years ago

Remove the toolhead, and look down through the hole in the platform where primers fall. Does the spe …In: spent primers

17 years ago

Yes, the chute is fully closed at the bottom.In: spent primers

17 years ago

When the handle is down, is the chute completely closed at the bottom? If not, replace the cotter …In: spent primers

17 years ago