Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
This is usually caused by an excessive amount of lube. Try reducing the amount a little and se …In: Dimples on the side of my case
18 years ago
Im sizing 223 and after i size the case i get dimples just under te neck is that normal?In: Dimples on the side of my case
18 years ago
No. The SDB won't keep the critical shoulder headspace dimension on the .357 SIG cartridge.In: 357 SIG for SDB?
18 years ago
Was there ever a SDB die set for 357 Sig? And how would I get one . . . Steve in TexasIn: 357 SIG for SDB?
18 years ago
I would like to try IMR 4895 with the small powder bar on my 550 for loading 223's. Think I wou …In: bridge
18 years ago
thanks, its good to know just in case i loose a die lady luck smiled on me and the 9mm #4 die show …In: resettting the tool dies for 9mm
18 years ago
18 years ago
This morning i started the procedure to reset everything for the 9mm i had purchased a second tool …In: resettting the tool dies for 9mm
18 years ago
Jimmied60, you obviously have some interest in machines or you would not be asking questions about r …In: New To Reloading
16 years ago
Your best bet is to start off with a good manual and read it cover to cover and see if you wish to p …In: New To Reloading
18 years ago
Hello, I am new to reloading. Any help that i could recieve would be greatly appr …In: New To Reloading
18 years ago
winchester brass, thanks for the insight, might have to try another brand and see if it goes away …In: time shure does fly by
18 years ago
powerboatr, What brand of brass were you getting the fail to fires? The fail to fires I was gettin …In: time shure does fly by
18 years ago
i went yesterday and had a few fail to fire , but did after i cycled the hammer again so i will lo …In: time shure does fly by
18 years ago
The SDB is a lot of fun. What I found is that reloading in itself is it's own hobby. I h …In: time shure does fly by
18 years ago
I love mine. I enjoy the reloading part about as much as the shooting part--to take all the co …In: time shure does fly by
18 years ago
Thanks I started off this evening around 6pm thought i would run a few rounds through and get an e …In: time shure does fly by
18 years ago
I share your concerns about the future of the Second Amendment. Do you have the article by Bar …In: the shape of things to come?
17 years ago
Obama Questionaire for prospective position holders http://graphics8.nytimes.com/packages/pdf/nati …In: the shape of things to come?
18 years ago
What causes that fail safe rod bushing rod bushing to snap in half? New to the 550 have had a Squar …In: Great service
10 years ago
Here was my Thank You letter I sent in
11/11/08
Dillon Precision Inc.
Re: RL550B
Customer# ### …In: Great service
18 years ago
I just wanted to give Dillon a public thank you for helping me with a problem I had with my .223 dec …In: Great service
18 years ago
If you don't push the handle all the way up it won't seat the primer and if you don't …In: powder at station #2
17 years ago
18 years ago
Here is a helpful trick so we don't forget in the future: I placed a sticker on my powder bar …In: powder at station #2
18 years ago
thanks i saw the magic we just ran 6 through to use as test subjects at teh range , if they go goo …In: powder at station #2
18 years ago
The powder only drops when a shell is in Station 2. The shell pushes up on the powder/expander …In: powder at station #2
18 years ago
As i was reading and learnng too operate my new reloader what keeps the powder and primer from dis …In: powder at station #2
18 years ago
The link changed that I mentioned above. The new links is:http://www.youtube.com/watch?v=k1g8ADJjJ- …In: Case trimmer
17 years ago
I trim my 223/5.56 every time, because it is so easy and that is how I resize the outside of the cas …In: Case trimmer
17 years ago
Does anyone have a video of the trimmer in use. I looked all over youtube & nothing came up with …In: Case trimmer
18 years ago
I use it regularly for 223 and 308. With a boattailed bullet, FMJ variety, I never chamfer the insid …In: Case trimmer
18 years ago
They told me on the phone at Dillon I didn't need to deburr the cases if I used the Dillon trim …In: Case trimmer
18 years ago
Not from us. It would be an expensive piece of carbide. I suspect a carbide tooling supplier could g …In: Case trimmer
18 years ago
I just bought a 650 & love the idea of the case trimmer for my .223. The question I have is can …In: Case trimmer
18 years ago
I just switched to the XL650 from an RCBS PRO2000. I never did like those APS strips. After having a …In: Switching presses ???
17 years ago
Yep you want the roller handle and the Strong mounts, Worth the time and effort. If you are having p …In: Switching presses ???
17 years ago
Alls it will take is the first blister in the palm of your hand after an extended loading session to …In: Switching presses ???
17 years ago
I have got it figured out now it just took a little bit. I have already run off about 2000 rounds of …In: Switching presses ???
18 years ago
I use the Lee dies with mine, I am a novice with this press as well, but no, we don't need the …In: Switching presses ???
18 years ago
I have used a RCBS rockchucker with the piggyback II for 15 years. I just bought a Dillon XL650 & …In: Switching presses ???
18 years ago
Thanks, I have a RL-450 and since there hasn't been a manual available for years it resolved my …In: shell plate problem
13 years ago
When you set the tension on the shellplate bolt, you next need to snug the brass-tipped set screw on …In: shell plate problem
16 years ago
I have started to have the problem you described where the shell plate bolt tightens each time the s …In: shell plate problem
16 years ago
I know it has been a while, but as a follow up, I sent the shell plate in, and they sent a new one a …In: shell plate problem
17 years ago