Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
Presuming you don't have any obstruction in your primer tube, then my diagnosis begins with the …In: Primers won’t drop into cup
5 years ago
All of a sudden my primers fail to drop into my primer cup. The slide bar goes all the way back, the …In: Primers won’t drop into cup
5 years ago
Hi,
Thanks so much for confirming the 550 will work for all identified calibers.
I should have got …In: Which Dillon Reloader is needed for .45-70 Caliber?
5 years ago
The short direct answer is that the 550 will easily handle the reloading chores for each caliber you …In: Which Dillon Reloader is needed for .45-70 Caliber?
5 years ago
Hi,
I'm new to this Forum.
Looking to buy reloader system, but do not want to make a mistake, …In: Which Dillon Reloader is needed for .45-70 Caliber?
5 years ago
Hi,
I'm new to this Forum.
Looking to buy reloader system, but do not want to make a mistake, …In: Which Dillon Reloader is needed for .45-70 Caliber?
5 years ago
Thank you everyone for the great advise and answering my NEWB question. Was confused and greatly ap …In: XL750 and Lee Dies
5 years ago
Your XL 750 will produce great ammo with the Lee dies I've been running the same set up as you …In: XL750 and Lee Dies
5 years ago
Your XL 750 will produce great ammo with the Lee dies I've been running the same set up as you …In: XL750 and Lee Dies
5 years ago
You will be good to go. The powder measure and powder die are in the basic press box. Have fun wit …In: XL750 and Lee Dies
5 years ago
I apologize, I had NOT opened the XL750 yet since I hadn't gotten dies, so I didn't realiz …In: XL750 and Lee Dies
5 years ago
Now on Station 2 can I use the Lee Expander die with the Dillon Powder Feed on the 750? I won' …In: XL750 and Lee Dies
5 years ago
I have loaded over 15k rounds of 9mm on the 750 with Lee dies.
I use the sizing/decap die, Lee seat …In: XL750 and Lee Dies
5 years ago
Bought a Dillon XL750 and got it quicker than expected actually minus the dies (9mm). They are back …In: XL750 and Lee Dies
5 years ago
Then... probably not!
My failsafe rod, on which I had to "tweak" the 90° bends to get it …In: Failsafe rod?
5 years ago
Can the old failsafe rod with the 90 degree bend be used with the new two piece powder measure syste …In: Failsafe rod?
5 years ago
5 years ago
Please see the two video links below, I need help diagnosing this. Im new to this machine and I have …In: Rl1100 primer slide is jerk-y
5 years ago
I see two possibilities. First, it is possible that the brass you are using has primer pockets that …In: Primer only goes in a little
5 years ago
I just bought and setup a Square Deal B .40. When I try to load, the primer is only pushed slightly …In: Primer only goes in a little
5 years ago
https://www.dillonprecision.com/kb/article/39/super-1050-primer-depth
If you click on the part numb …In: High Primers
5 years ago
I am having difficulty with my Primers. They are high and not flush with the case. I have taken th …In: High Primers
5 years ago
Unfortunately, I am a newbie also having just received a no caliber RL1100 a week ago. Your setup at …In: Setup
5 years ago
Newbie looking for some direction. Considering the >20 week backorder - I really need to order th …In: Setup
5 years ago
I just recieved a Dillion RF100 from a friend and need to get some parts. I cannot find them on your …In: RF100 Parts
5 years ago
I tightened up the shell plate, adjusted the seating die, and ran another batch of 100. This batch …In: Varying OAL in 9mm
5 years ago
Tighten your shell plate until it wont turn then back it off a bit. If that doesn't work there …In: Varying OAL in 9mm
5 years ago
Yes, and I tried both sides. I stuck with the side for round nose as it kept these truncated cone b …In: Varying OAL in 9mm
5 years ago
If you have the Dillon die set, are you aware that the seating stem can be turned-over? One side is …In: Varying OAL in 9mm
5 years ago
I am pretty new to reloading on a progressive. I just got my XL750 set up last week. My first 100 …In: Varying OAL in 9mm
5 years ago
Do you have a #1 Shellplate in another kit such as .45 ACP or .308 Win that you could try? The only …In: Load 7x57 on a 650?
5 years ago
So there isn’t a caliber conversion kit for this caliber but would the .270 win kit work for this? B …In: Load 7x57 on a 650?
5 years ago
5 years ago
Well they are not the same. The OD on the brass bearing is 1.035" and the OD on the Delrin bear …In: link arm bearings
5 years ago
I have a 2001 SD with brass bearings. Would the older Delrin bearings work just as well?In: link arm bearings
5 years ago
Mine does the same thing with the Dillon dies. Don't know if there is a fix.In: Spent primer problems
5 years ago
Let me clarify and add to my prior post, I only encounter this issue using the Dillon spring-loaded …In: Spent primer problems
5 years ago
I have had the same issue. I replaced the cotter pin with a small straight piece of wire. Bent the t …In: Spent primer problems
5 years ago
Kerry,
This is the kind of response demonstrating that Dillon owner/operators are smart resourceful …In: Spent primer problems
5 years ago
Terry I got lucky I had a good supply of small rifle primers and have been going to gunshows and tra …In: Spent primer problems
5 years ago
I have had the problem myself and seen it written about so frequently that I concluded it was just a …In: Spent primer problems
5 years ago
I replaced mine with a straight section of a paper clip, never had a problem in over 30 years.In: Spent primer problems
5 years ago
After reloading for over 40 years and wanting a Dillon for the last 20 I finally bought a RL550 C I …In: Spent primer problems
5 years ago
I'm attempting to set up my MBF for .300 BLK using Sierra 125 gr spire point flat base bullets. …In: 300 BLK dropper adjustment
5 years ago
Can you cause the jam up by manually rotating the shell holder plate manually?
My locater pins hav …In: jamming on locator pins
5 years ago
They appear to be fully inserted / pushed into the shell plate, this is on my press set up for 9mm.In: jamming on locator pins
5 years ago
Are the shells getting pushed into the shell holder sufficiently to clear the locater pins? What ca …In: jamming on locator pins
5 years ago
I recently had to remove case feeding portion of my 650 when the indexer return spring broke - havin …In: jamming on locator pins
5 years ago