Forum Navigation
Please Login to create posts and topics.
Post History: Reloader
HI all,
My XL650 started crushing primers and after a phone session with Dillon, they decided to …In: Dillon XL650 alignment - frustration
6 years ago
Correction. When I wrote "44 Colt" I meant to write "45 Colt". What can I say? …In: OAL variation with new brass?
6 years ago
Great analysis. As I read your report it occurs to me that you have a situation similar to one I ex …In: OAL variation with new brass?
6 years ago
Correction, I aimed for 1.255 with the new starline, and left everything set as is for the rest. Mea …In: OAL variation with new brass?
6 years ago
Thank you for the insight. And yes, I'm trying to be as careful as possible.
I only had issue …In: OAL variation with new brass?
6 years ago
You've raised a few different issues and I'll offer my thoughts on each. The OAL is reall …In: OAL variation with new brass?
6 years ago
I'm a fairly new reloader. I've loaded a large amount of 9mm and 45acp, and I just started …In: OAL variation with new brass?
6 years ago
To the original poster. I’m having the same issue. Did you get it resolved? If so, what was the so …In: Primers not dropping into cup
6 years ago
6 years ago
Same issue I have here https://www.dillonprecision.com/primer-pick-up-issue_350_32_4403.htm.
Haven& …In: Primers not dropping into cup
6 years ago
I’ve had my 750 for a few weeks and this issue just started today. Primers are not dropping into the …In: Primers not dropping into cup
6 years ago
So to start off I already had an XL650 setup for 45ACP, love it.
Just received my new XL750 which I …In: Excellent
6 years ago
I just got my first Dillon I bought it like new from a reloading company. It was a spare the was nev …In: Spend primer bouncing out of the bin.
6 years ago
6 years ago
You might have to turn the die down an additional 1/8 to 1/4 turn beyond the dies contacting the she …In: Full length sizing .300 Win Mag
6 years ago
Hi guys,
today I got my conversion kit for .300 Win Mag.
I've started just with the FL sizing …In: Full length sizing .300 Win Mag
6 years ago
6 years ago
On my 750, I had to back out the set screw a 1/4 turn to let the primer bar travel further back on t …In: Primer pick up issue
6 years ago
Newbie to the 750. Now the primer system only works intermittently.
I will get 5-6 pick ups with th …In: Primer pick up issue
6 years ago
Ive also noticed that small primer punch is snug about 1/2 way up...Im going to chase the threads a …In: Poor Threads On Small Priming Seat
6 years ago
I've owned my 650 for several years loading .45 ACP. It came equipped with two primer seating …In: Poor Threads On Small Priming Seat
6 years ago
6 years ago
Has anyone loaded 38-55 cartridges on an XL-650? If so, which shellpate and powder funnel are you u …In: 38-55 on XL-650
6 years ago
If you are talking about seeing the shape of the bullet or bullet base through the brass that is nor …In: 45 ACP Case Expanding
6 years ago
Hi,
New to loading so forgive the lack of knowledge, I am setting up the dies and I have 1 and 2 se …In: 45 ACP Case Expanding
6 years ago
I have been wondering the same thing. After looking at the Xl 750 and the Loadmaster I believe it ca …In: powder drop in station 1
5 years ago
I don’t know what a bullet feed is but if it means putting the bullet in place I think it would be b …In: powder drop in station 1
6 years ago
Station 1 is for resizing and decapping. Station 2 for priming and powder charge. You can't c …In: powder drop in station 1
6 years ago
i recently upgraded from a lee loadmaster to a 650. on my loadmaster i was sizing on a single stage …In: powder drop in station 1
6 years ago
The only time I had this difficulty was when I had over cleaned the brass. I only dry vibrate for 1 …In: 9mm brass sticks to powder funnel
5 years ago
I just replaced all the 9mm dies in my SDB as part of my process to refresh the setup. I had the sam …In: 9mm brass sticks to powder funnel
6 years ago
mine will do this 45 acp rounds after a few hundred. I take out the plunger and wipe it clean and th …In: 9mm brass sticks to powder funnel
6 years ago
Very little, just to fit the bullet. Using a .356 bullet I measured the max outer diameter of the fl …In: 9mm brass sticks to powder funnel
6 years ago
After dispensing the dropped powder, the powder funnel seems to stick to the powder funnel, requirin …In: 9mm brass sticks to powder funnel
6 years ago
I am having the same problem with my 550C. I just got a second brand new small primer seating assem …In: Primer seating not deep enough
6 years ago
Also I did switch it to the small rifle primer when changing it to 5.56 from 243 win.In: Primer seating not deep enough
6 years ago
Hello, I purchased a Dillon 550C, and I picked up recently an older 550 possibly the B series. On my …In: Primer seating not deep enough
6 years ago
To reliably get support from Dillon, you probably need to fill-out that Technical Support Request Fo …In: Case Not Centering in Station 1
6 years ago
No. Second time I've asked.....the difference in the diameters of the .223 and .204 aren' …In: Case Not Centering in Station 1
6 years ago
I usually have an issue with .204 Ruger cases not centering on the decapping die. Since they're …In: Case Not Centering in Station 1
6 years ago
Same thing here... only the On/OFF button works... they are shipping another... Dillon obviously kno …In: D-Terminator digital scale buttons not working
6 years ago
And another FYI, so you know I am not bashing DIllon. I am bashing that scale. When I get further in …In: D-Terminator digital scale buttons not working
6 years ago
If you are on the fence. DO NOT DO IT. Find another. I called them. Waited an hour on phone (not an …In: D-Terminator digital scale buttons not working
6 years ago
Manufacturer is CED.
Just got off the phone with Dillon Support and they are going to send out a ne …In: D-Terminator digital scale buttons not working
6 years ago