Forum Navigation
Please Login to create posts and topics.
Post History: The Human Manual
I will happily forward your idea to our R&D and Marketing departments. Thank you for the input.In: Dillon Bullet Feeder - Quick-Change Parts
11 months ago
We prototyped a steel shot dispenser. That might actually go into limited production eventually, as …In: SL 900 - Can A Machine Shop Make it 3
11 months ago
On your shot drop tube; it is steel with a round hole, or a cast alloy with a hexagon-shaped hole? T …In: Small amounts of shot everywhere
11 months ago
It's on a back burner for now. Other projects in engineering are getting priority.In: SL 900 - Can A Machine Shop Make it 3
11 months ago
Email received, now in the hands of the International Sales Director. Steve will take care of you!In: Cases getting under casefeeder plate.
11 months ago
Please email me your contact information, and customer number if available.
Send it to gary.ki …In: Cases getting under casefeeder plate.
11 months ago
I am bringing this to the attention of the Director of our international sales for further review at …In: Cases getting under casefeeder plate.
11 months ago
Ballistol,
Your case feed bowl has to be sent in, so we can replace it under warranty and move th …In: Cases getting under casefeeder plate.
11 months ago
The bulging is probably occurring at the crimping station. Use a headspace case gage to adjust the s …In: 223 cases developing a slight shoulder bulge
12 months ago
First, what size of shot are you using? next, inside the shot measure housing is a machined recess w …In: Small amounts of shot everywhere
12 months ago
You are correct in that your current powder charge is not at high enough pressure to expand the case …In: Sizing unfired Starline brass
12 months ago
It is a good idea to size new brass, at least to ensure that case mouths are round. In your case, th …In: Sizing unfired Starline brass
12 months ago
12 months ago
The ratchet is a quality control mechanism. If you fail you fully lower the handle, the ratchet tab …In: RL1100 and Super 1050 toolheads: interchangeable?
12 months ago
No problem if you are using polymer-coated lead bullets. If you are using lead bullets with conventi …In: bullet feeder for 45 acp
12 months ago
I have had quite a few customers who lack room for a permanent bench do exactly that. Another option …In: New to reloading
12 months ago
It will vary a bit, as all powders have different densities. But as a guideline, as follows:
stan …In: Chart/Table for caliber vs Powder Bar needed?
1 year ago
The raw castings are the same for both the XL750/650 and SL900 frames. However, the secondary machin …In: Conversion kit for existing 650?
1 year ago
Actually, remove the E-Clip on the very top of the size/deprime die. Both the depriming pin and the …In: Can the Depriming Pin be Rremove, so new pre-primed hulls can be used?d
1 year ago
The B funnel is correct. Measured from top to bottom, the B funnel should be 1.220" long, +/- . …In: 308 powder funnel too short?
1 year ago
Your 38 Special conversion kit will also load 357 magnum cartridges. From 38 Spl to 357, you will b …In: Dual cartridge die conversions vs single cartridge?
1 year ago
No question, the longer bearing surface of the 147 grain bullets exaggerates the coke-bottle shape. …In: Coke Bottle 9mm
1 year ago
Not a problem at all. 9mm is a tapered case, not a straightwall. When the case is sized, the case ne …In: Coke Bottle 9mm
1 year ago
Is any powder leaking onto the top of the toolhead, or just the top of the shellplate? If leaving o …In: Vihtavuori N320 Leakage from Powder Measure?
1 year ago
Literally just the actual XL750 machine only. The case feeder, toolheads, conversion kits, powder me …In: 650 to 750
1 year ago
Lets check some basics first. What cartridge are you loading? What numbers/letters are stamped on th …In: binding in de-priming action
1 year ago
With online orders, the billing and shipping addresses must match exactly, or the order will be reje …In: declined credit cards
1 year ago
Interesting. We've used the orange based waterless hand soap to clean them in the past. The cur …In: Powder measure staining - how to remove
1 year ago
You will need to 22-250 case feed adapter, a modified orange one. #14313 and the 6PPC powder funnel …In: 6 Dasher conversion kit for XL650
1 year ago
I assume you are seating the bullet out far enough to engage the rifling? If so, you should have no …In: Rel 15 for fireforming
1 year ago
The extra small powder bar is the same, regardless of which Dillon loader you are using. It is inten …In: Reloading 32S&W long WC with just 1,3grain in XL750
1 year ago
If you are using a coarse flake powder, such as Unique or 800-X, it might be of benefit. For ball/sp …In: Thoughts on vibrating the powder measure
1 year ago
Case lube and size die lube are the same thing. The lube used will not increase or decrease the amou …In: Full Length Sizing Die
1 year ago
No problem loading 32 H&R Magnum. Negative on the 327 Federal, however. The webbing is too thick …In: .32 H&R and .327 Federal on a SDB
1 year ago
The powder measure die is not threaded deep enough into the toolhead. Use a sized case to activate t …In: Powder Measure Inconsistant Drops/Actuation
1 year ago
When you order the bullet feeder, one dropper die comes with it as part of the base caliber. Separat …In: Mr Bulletfeeder for XL650 correct parts to order
1 year ago
Install the new bolt, then cycle the handle at least 4 times to determine if the shellplate is rotat …In: Index bolt for older Square Deal?
1 year ago
The only potential issue is if you already use a powder check die in your 650 toolhead. The DAA Mr B …In: XL650 with Alpha Bulletfeeder
1 year ago
I'm not aware of anyone offering a case gage for 7.5 x 54mm. As I also have a MAS36 rifle, i us …In: Reloading 7.5x54 French MAS?
1 year ago
Dillon doesn't make dies for all cartridges by any means. We carry Redding dies for the common …In: 6.5 Creedmore dies?
1 year ago
The article is in the outgoing Blue Press magazine, December 2024 issue. It is in the mail now. Hope …In: Reloading 7.5x54 French MAS?
1 year ago
If you plan to used fired 30-06 brass to form into 7.5 MAS, then I strongly recommend that you annea …In: Reloading 7.5x54 French MAS?
1 year ago
It depends on whose brass you are using. Usually the #1 shellplate works fine. If it is too tight, u …In: Reloading 7.5x54 French MAS?
1 year ago
There is not a video to drop the shaft, but it is straightforward. No readjustments are required.
…In: primer slide travel
1 year ago
You cannot overtighten the overtravel block. There is a burr at the bottom of the roller ramp which …In: primer slide travel
1 year ago
Station 1 locator B #13156
K powder funnel #13216
Yellow case feed arm bushing #13619
Large …In: 6.5 PRC Conversion Kit Parts
2 years ago
On the primer feed, simply detach the cam located on the upper right side of the frame. This is only …In: Machine improvement
2 years ago