Forum Navigation
Please Login to create posts and topics.
Post History: The Human Manual
The Dillon handgun dies have a spring-loaded depriming assembly to help reduce this. There are two d …In: Spent primers not dropping free from decapping pins
2 years ago
In general, all brands of primers are interchangeable. Keep in mind this does not mean you can subst …In: Primer Differences ???
2 years ago
Piston Skeet Light 12ga 25mm wad (250/bag) (ballisticproducts.com)In: Stack height issue with 3/4ounce 12 gauge loads
2 years ago
If your crimps are pushing up like in the photo, something in your hull/powder charge/wad/shot volum …In: Stack height issue with 3/4ounce 12 gauge loads
2 years ago
Cycle the handle without any cases in the loader, but with primers in the feed tube. When you lift t …In: Twisted Small Primers
2 years ago
Your problem is the primer cup coming up through the shellplate. This has nothing to do with the de …In: Twisted Small Primers
2 years ago
No flared case should drop into the gage fully. Your size die is good. Check your ammo after crimpin …In: Changed from .45 ACP to 9mm —> Now getting bad yield and changing COLs
2 years ago
Remove the primer feed, then detach the primer slide from the primer feed. Measure from the undersid …In: Twisted Small Primers
2 years ago
We typically recommend flaring the case mouth at least .010" larger than a sized, unflared case …In: Changed from .45 ACP to 9mm —> Now getting bad yield and changing COLs
2 years ago
I wonder if you reverse the direction of indexing, and feed the loaded cartridges into station 4, if …In: recurring problem
2 years ago
Re-check the platform alignment using the platform alignment tool that cam with the frame change kit …In: Stage 1 Problems
2 years ago
What we considered offering was a kit consisting of just enough parts & pieces to convert an XL6 …In: 750 BL ?
2 years ago
Prior to the great plague, we seriously considered offering a very stripped version of the 750, so a …In: 750 BL ?
2 years ago
No. However, there is a measurement from the underside of the primer bar to the top of the primer cu …In: Question on primer pocket position
2 years ago
Check the pockets in the shellplate for damage. Excessively expanded cases can develop enough frict …In: Decapping / Deprimer - Stage 1 stuck
2 years ago
The 5.7 x 28 brass has a light varnish coating. This coating acts as a lubricant for feeding rounds …In: Working with 5.7 brass
2 years ago
2 years ago
Some brands of 40 S&W brass have crimped primer pockets. After the crimp is removed, either by s …In: Primer only goes in a little
2 years ago
We have found as much a .001" eccentricity in current domestically produced primers. They shoul …In: Last primer in the primer feed tube is hanging up.
2 years ago
You will need the XL powder die, #21253. Unless the cartridge requires over 50 grains of powder, you …In: 475 Linebaugh Questions
2 years ago
The toolhead design of the Square Deal will not maintain a consistent headspace on bottleneck cases. …In: New Square Deal specifically for AR15 rounds (small rifle)...?
2 years ago
The cause of the sticking is the cleanliness of the interior of the cases. On fired cases, the light …In: Flare stage - requires too much pressure to release
2 years ago
If you are new to reloading, head over to our educational website www.reloader.com for a basic educ …In: Help
2 years ago
you have to exchange the primer seating assembly, primer disc and primer magazine tube when switchin …In: 9mm to 45acp
2 years ago
Unfortunately, that connector body collar you were sent is not compatible with the SDB machine. If y …In: SDB has a new powder measure collar assembly
2 years ago
Welcome!
Thank you for your patronage and support of our forum. Dillonprecision.com has a bunch …In: New member
2 years ago
If the projectile has a cannelure or crimp groove, then a taper crimp will have a place to go. Match …In: .223 Crimp
2 years ago
The shot drop tube is easily replaced. It is secured into the shot dispenser base by a single set sc …In: Stack height issue with 3/4ounce 12 gauge loads
2 years ago
Try backing the shot dispenser up, to reduce how deep the wad is seated.In: Stack height issue with 3/4ounce 12 gauge loads
2 years ago
Is your shot charge level with the top of the wad, or below it? Looking at the Hodgdon website, Tite …In: Stack height issue with 3/4ounce 12 gauge loads
2 years ago
When the primer magazine is empty, unscrew the knurled cap , remove the aluminum magazine tube. Cut …In: Primer dropping issues
2 years ago
THis blue block is bolted to the inside wall of the bowl. On the outside you can see the two bolt he …In: Case feeder binding
2 years ago
Toolheads do not interchange between the 550 and 750 loaders. The 550 has 4 stations,, whereas the 7 …In: Dillon RT1500 Confusion
2 years ago
You probably need to adjust the blue block bolted inside the bowl. Raise the leading edge, and lower …In: Case feeder binding
2 years ago
We recommend using a case lube based on lanolin. Dillon Precision, Midway USA both offer a pump spra …In: Dillon RT1500 Confusion
2 years ago
Are you certain the problem is in depriming? Remove the depriming assembly and see if the effort nee …In: Dillon RT1500 Confusion
2 years ago
wrap a strip of scotchbrite around a mandrell and use that you clean the interior of the top of the …In: Dillon RT1500 Confusion
2 years ago
2 years ago
If you are full length resizing your cases first, then it is quite likely that cases are spinning in …In: Dillon RT1500 Confusion
2 years ago
Use the 270 Winchester conversion kit #21093. The 284 case rim is too small for the 7mm WSM shellpla …In: Conversion kit for 284 Winchester
2 years ago