Comments
Comments
3D printed. They have a lifetime warranty on all non-electronic components of the bullet feeder.In: Dillon Bullet feeder question
6 months ago
Thanks for providing the link. Our IT folks will probably add a redirect to that link to reroute use …In: Last Blue Press issue posted a year ago??
6 months ago
There are links for up through October 2025 currently. Blue PressIn: Last Blue Press issue posted a year ago??
6 months ago
See if the misfires only occur on one or two brands of brass, or if it occurs on a wide variety?In: Inconsistent Primmer Seating Depth on RL1100
6 months ago
You have the proper dies in the correct stations. Yes, you need to install and adjust the Lyman die …In: RT1500 Trimer setup on 750
6 months ago
I can see that the burr left after the primer flash hole was punched has been flattened during depri …In: Inconsistent Primmer Seating Depth on RL1100
6 months ago
Back out the swage backup die above the swager, so it doesn't contact the cases at all. With th …In: Inconsistent Primmer Seating Depth on RL1100
6 months ago
Pick out a handful of commercial cases, disengage the swager, then run them through the loader. Seat …In: Inconsistent Primmer Seating Depth on RL1100
6 months ago
With the handle up, push down on the edge of the shellplate at station 7, the bullet seating positio …In: Inconsistent Primmer Seating Depth on RL1100
6 months ago
My first suspicion is that the case pockets in the shellplate are deformed, either from excessive sw …In: Inconsistent Primmer Seating Depth on RL1100
6 months ago
Don't worry about cleaning primer pockets. You won't get enough buildup to prevent seating …In: Primer pockets - How clean is clean enough?
6 months ago
The hopper on the Dillon powder measure already has a baffle molded into the bottom of the tube. If …In: Would adding a powder baffle help with H-110 300BO loads on my 2010-2011 Dillon 550?
7 months ago
On his been invoiced out, should ship tomorrow.
At your service!In: H110 powder leaking on my 550B powder measure?
7 months ago
Are you pulling bullets from military ammo, civilian factory ammo, or reloads? Reloads should disass …In: Pulling 223 bullets
7 months ago
There are a few powders out there whose granule size tolerances overlap our powder measure tolerance …In: H110 powder leaking on my 550B powder measure?
7 months ago
It sounds more like your primers aren't fully seated. In your case, the first strike finishes s …In: Creating mild loads for .460 revolver
7 months ago
All you need to do is to remove the shellplate, lift the index pawl #13667 out of the top of the rin …In: Can I convert an XL650 to something like a 550 model without the auto progression?
7 months ago
No problem using a cast or polymer coated bullet in .452" diameter in your .460 S&W. You w …In: Creating mild loads for .460 revolver
7 months ago
We do sell the XL650 primer feed separately. #20982 cost $129.00 You can purchase one in our Retail …In: Is the XL650 large primer system still available from Dillon?
7 months ago
When you hook up the failsafe return rod, be sure the rod goes into the oval hole in the rear plate, …In: Powder measure question
7 months ago
When activated by a case, the powder bar should go to full travel somewhat before the handle bottoms …In: Powder measure question
7 months ago
It's a bit ugly. I doubt this would cause any inconsistency, but this adjustable insert should …In: Powder measure question
7 months ago
You have a +/- tolerance of about 1/8", so no need to be .001" accurate. But yes, remov …In: clearance above for a case feeder?
7 months ago
You could shorten the top of the case feed post and the bottom of the clear plastic case feed drop t …In: clearance above for a case feeder?
7 months ago
My apologies for the delays in getting you loading again. Happy to hear you are cranking out ammunit …In: Case feeder not working
7 months ago
Measuring from the top of the strong mount (where the machine bolts to it) to the top of the case fe …In: clearance above for a case feeder?
7 months ago
The bullet seating die is designed to straighten the bullet before it is seated into the case. As lo …In: How important is bullet placement
7 months ago
Call or email us, and request a return authorization to send you r primer feed in to be rebuilt. The …In: new primer slides do not fit in my Primer Housing and Shield
8 months ago
You should have received an email secure payment link for the shipping costs. We are covering the mo …In: Case feeder not working
8 months ago
If the case mouths line up with the dies, and the primer comes up through the hole in the shellplate …In: Base Disc Mounting Screws - 13860
8 months ago
Use the headspace case gage to adjust the trim die body first. Then adjust the height of the trimmer …In: 223 processing die setup suggestions
8 months ago
Did you use a headspace case gage to adjust the trim die? Used unsized brass to check this.
Push …In: 223 processing die setup suggestions
8 months ago
I might be able to aid you, but some documentation would help. Do you have a copy of the receipt, es …In: Case feeder not working
8 months ago
Unfortunately, should you have a primer detonation, this becomes the new vent hole for all the debri …In: Include a peephole on the XL750 primer feed housing
8 months ago
9 months ago
Then either phone or email us and request a replacement for a defective shim. #62329. Make clear it …In: First post: primer feed issue on XL750
9 months ago
There is a thin black steel shim plate underneath the primer slide. This is a wear surface to preven …In: First post: primer feed issue on XL750
9 months ago
Boog,
First, remove the operating rod from the side of the primer feed. Pull the machine handle d …In: First post: primer feed issue on XL750
9 months ago
We aren't finished adding calibers to the bullet feeder. Check back in a few months.In: Bullet Feeder Calibers?
9 months ago
First, see if you can rotate the shellplate by hand. If not, then back up the shellplate bolt 1/8 tu …In: Failing to advance
9 months ago
Yes you may. A small amount, just enough to thinly cover a few threads should suffice.In: Index Assembly screw
9 months ago
The spring should hold the wad guide sleeve up. Use a very light oil on the outside of the sleeve, t …In: wad guide sleeve and hull interference
10 months ago
If your crimps are slightly collapsed in the center, then back the central plug in the top of the fi …In: Guidance for stack height (12 gauge)
10 months ago
Cut a 1" wide strip from a dryer anti-static sheet, wrap it around a bore brush, and wipe out t …In: Delayed Powder dropping
10 months ago
Try this: unplug the unit, detach the clear plastic funnel from the front of the bowl. detach the …In: Case feeder not working
10 months ago
Unfortunately, there is too much variation in fired hull length to establish a fixed dimension for t …In: Guidance for stack height (12 gauge)
10 months ago
It depends on what you are applying this to. It can cause greater variation in case neck tension, wh …In: What is the effect of inside neck case lube on powder charging on a RL1100 or Super 1050 ?
10 months ago
Your concept is going to be adopted. I suspect the price on a conversion kit will go up slightly, bu …In: Dillon Bullet Feeder - Quick-Change Parts
11 months ago
