Please to create posts and topics.

Post History: ARMTGuy

ARMTGuy

User

The size die always sizes the case tighter than new factory cases. The case is expanded by the bulle …In: 45acp bulge top of the case

2 years ago

The 750/650 ejector wire was redesigned years ago. In our experience, running the shellplate bolt to …In: XL650 Ejector Wire Problem

2 years ago

Use a lubed, fired case to set the headspace for the trim die. The trim die should at least tough t …In: 308 Carbide Trim Die problem

2 years ago

My suspicion is that one or both of your link arms might be torqued slightly. We have created a retu …In: Powder drop not lining up with case

2 years ago

It would be very unusual for the shellplate bolt to loosen, as the shellplate rotates in the clockwi …In: Shell plate bolt keeps loosening

2 years ago

Without any cases in the shellplate, and with primers in the tube, cycle the handle. DO any primers …In: Primers jumping out of the cup or loading sideways......

2 years ago

Push down on the edge of the shellplate at station 4. If it feels springy, then the shellplate bolt …In: Powder drop not lining up with case

2 years ago

No question that the undersized case rim is the cause. Use of case lube might prevent this, but the …In: Case rim shaving off, stuck case

2 years ago

The 45 Colt case has a lot of surface area. Try a light spray of case lube. Additionally, measure th …In: Case rim shaving off, stuck case

2 years ago

5.7 x 28mm has a case head too small to stabilize the case when priming. Additionally, the case leng …In: 5.7/28 conversion kit for the 750

2 years ago

If you don't expect to use the dies within 6 months or so, and you live in a humid area, apply …In: Toolhead storage

2 years ago

Not sure what your issue really is. Some brands of dies have a shorter threaded portion than other …In: Sizing Die will not screw down far enough

2 years ago

https://vimeo.com/508527277 In: Cases Slide Back from Station One

2 years ago

These are swage backup dies from the 1050/1100 industrial machines.In: Dillon Die Identification?

2 years ago

We are in the process of making a shellplate for the PRC cartridges. Check back in a week or two.In: Reloading 6.5 PRC on the 550

3 years ago

Did you remove the platform in order to search for the pawl? If yes, then you really need an alignme …In: 650XL index pawl

3 years ago

The powder and shot bars are fully adjustable on the SL900. Use a 7/16" wrench to turn the bolt …In: Adjustable Powder and Shot bars

3 years ago

Not at this time. So order the following: 308 conversion kit for the RL550 #20130 Steel 308 di …In: 550? Change over from 9mm to .223

3 years ago

20113 is NOT a caliber conversion kit. It is a generic toolhead assembly. This is what the bullet se …In: What caliber conversion is this

3 years ago

We've offered "E-Z Change kits" in a very few common calibers in the past. We deactiv …In: 550? Change over from 9mm to .223

3 years ago

The most likely cause is the spent primer is getting wedged onto the tip of the decap pin as it is p …In: Deprime issue

3 years ago

As of July 1, 1999, the warranty on electronic/ eletrical components was limited to one year; the mo …In: Interesting conversation with Dillion.

3 years ago

with a full metal jacket projectile, your overall variation of .007" is actually on the low sid …In: Seat and Crimp

3 years ago

Not quite yet, as we are waiting for the shellplates to get finished. We received one batch of shell …In: Calibers

3 years ago

Use the Square Deal B powder die, # 13865 and Square Deal B powder die clamp #13764 on the 450 JrIn: RL450JR-B

3 years ago

Order kit 20237 for 308 Marlin Express. The powder funnel and shellplate are both different from 308 …In: conversion kit rl550b

3 years ago

The only difference is that the powder die included with the 1050/1100 measures is heat treated for …In: Difference between powder measures

3 years ago

A primer doesn't have to be much out-of-round to bind in a primer tube. Sounds like you were ca …In: primer stuck in loading tube!

3 years ago

I greatly appreciate the kind words. Should you ever need assistance that isn't covered by a v …In: Thank you Gary The Human Manual!

3 years ago

Spray WD-40 into the open end of the primer. Bend the tube. Via email, send us a photo of the bent t …In: primer stuck in loading tube!

3 years ago

If you move the case feed slide by hand, does it move freely and smoothly to its limits in both dire …In: How to Replace the Case Insert Slide Spring (#23)

3 years ago

dividing the bowl would dampen the scrubbing movement of the media, and not clean anything. If you&# …In: Small Batch Vibratory Tumbling

3 years ago

We are still waiting for shellplates to be delivered. Once they are available, we will list them onl …In: 6mm ARC

3 years ago

Use the ^PPC powder funnel #13085, The 6mmARC Casefeed Adapter #62427, 6mm ARC Shellplate #75127. Th …In: 6mm ARC

3 years ago

We do #62452 XL750 / XL650 Caliber Conversion Kits (dillonprecision.com)In: 6mm ARC

3 years ago

If you can find a copy of the Laser-Cast Reloading Manual, first edition, they have pressure-tested …In: 250 Grain/.451/45 ACP loads

3 years ago

Almost. The only difference is in the length of the ratchet bolted to the back of the toolhead. The …In: RL1100 and Super 1050 toolheads: interchangeable?

3 years ago

The Dillon Precision die instructions have always made it clear that what you described is merely TH …In: Reloading 556 - Interesting Observation - But Begs The Question

3 years ago

We recommend you measure the case mouth diameter on a sized, unflared case. After flaring, the case …In: XL650 - Shaving Projectiles

3 years ago

The cases are sticking to the powder funnel. This is common with new brass and wet-cleaned brass in …In: Difficulty on the downstroke

3 years ago

Push down on the edge of the shellplate at station 4. If it feels springy, then the shellplate bolt …In: XL 750

3 years ago

We made these brass ends for use on the XL650, and have completely divorced ourselves from them. We …In: Primer magazine tube ends (the red and blue ones)

3 years ago

This brass is still safe to reload and shoot.In: Discoloration of brass after ultrasonic cleaning

3 years ago

Slowing your handle downstroke speed so that it takes at least one full second to fully move the pow …In: Extruded powder small mouth cases

3 years ago

It sounds like your cases are varying enough in internal volume for the sensor to sound the alarm. Y …In: Powder Check Rod Sticking

3 years ago

Please post some photos, or send them to support@dillon-precision.comIn: magnum rifle case feeder assy issue

3 years ago

For trimming 300 BLK, we now have a short trim die toolhead, Modified RL550 Toolhead for RT1500 Trim …In: RCBS small base 300 blk

3 years ago

Readjust the seat die body. It sounds like the crimp ring in the top of the seat die is pushing ever …In: Reloading 300 Weatherby...Squishing Brass!

3 years ago

In your case, the wrong carbide ring was installed into the size die body. You would have to use pin …In: 9 mm Dillon carbon sizer question

3 years ago

If the shellplate bolt is a bit loose, this happens. Push down on the edge of the shellplate at stat …In: Powder throw on shell plate

3 years ago